Fabia Mk2
Removing and installing parts of the injection system |
For engine with identification characters BME |
1 - | Engine cover with air filter |
q | removing and installing → Chapter |
q | disassembling and assembling → Chapter |
2 - | Cable guide |
q | clipped onto the intake manifold |
3 - | Connector |
q | for oil level and oil temperature sender -G266- |
q | only for vehicles with extended service intervals (WIV) |
q | 3-pin |
4 - | Connector |
q | 2-pin |
q | for injection valves -N30…N32- |
5 - | Connection for fuel supply hose |
q | from fuel filter |
6 - | 8 Nm |
7 - | Fuel rail with injection valves |
q | disassembling and assembling → Chapter |
8 - | Vent valve |
q | Vent fuel system → Chapter |
9 - | 20 Nm |
10 - | Intake manifold |
q | disassembling and assembling → Chapter |
11 - | Lambda probe upstream of catalytic converter - G39-, 50 Nm |
q | Fitting location: in the exhaust manifold |
q | coat only thread with hot bolt paste -G 052 112 A3 -; hot bolt paste must not get into the slot of the probe body |
12 - | Connector |
q | 4-pin |
q | for lambda probe upstream of catalytic converter -G39- |
q | black |
q | Fitting location → Chapter |
13 - | Lambda probe downstream of catalytic converter -G130-, 50 Nm |
q | Fitting location: downstream of catalytic converter |
q | coat only thread with hot bolt paste -G 052 112 A3 -; hot bolt paste must not get into the slot of the probe body |
14 - | Connector |
q | 4-pin |
q | for lambda probe downstream of catalytic converter -G130- |
q | Brown |
q | Fitting location → Chapter |
15 - | Coolant temperature sender -G62- |
q | before removing, reduce pressure in cooling system if necessary |
16 - | O-ring |
q | replace |
17 - | Retaining clip |
q | check tightness |
18 - | 8 Nm |
19 - | Coolant regulator housing |
q | disassembling and assembling → Chapter |
20 - | Retaining clip |
q | check tightness |
21 - | 52- and 28-pin plugs |
q | for control unit Simos -J623- |
q | only insert or remove plug when the ignition is switched off |
q | unlock the multi-pin plug connection before pulling out |
22 - | Engine control unit |
q | Control unit Simos -J623 - |
q | Fitting location → Chapter |
q | Check supply voltage → Current flow diagrams and Fitting locations |
q | replace → Chapter |
q | Coding → Vehicle diagnosis, testing and information system VAS 5051 |
23 - | Support |
24 - | 2 Nm |
For engine with identification characters BZG, CGPA |
1 - | Connecting hose |
2 - | Open warm-type clamp |
3 - | Air filter |
q | disassembling and assembling → Chapter |
4 - | Intake manifold |
5 - | Cable guide |
q | clipped onto the intake manifold |
6 - | Connector |
q | for oil level and oil temperature sender -G266 - |
q | only for vehicles with extended service intervals (WIV) |
q | 3-pin |
7 - | Connector |
q | for injection valves -N30…N32- |
q | 2-pin |
8 - | Connection for fuel supply hose |
q | from fuel filter |
9 - | 8 Nm |
10 - | Fuel rail with injection valves |
q | disassembling and assembling → Chapter |
11 - | Vent valve |
q | Vent fuel system → Chapter |
12 - | 20 Nm |
13 - | Intake manifold |
q | disassembling and assembling → Chapter |
14 - | Lambda probe upstream of catalytic converter - G39-, 50 Nm |
q | Fitting location: in the exhaust manifold |
q | coat only thread with hot bolt paste -G 052 112 A3 -; hot bolt paste must not get into the slot of the probe body |
15 - | Connector |
q | 4-pin |
q | for lambda probe upstream of catalytic converter -G39- |
q | black |
q | Fitting location → Chapter |
16 - | Lambda probe downstream of catalytic converter -G130-, 50 Nm |
q | Fitting location: downstream of catalytic converter |
q | coat only thread with hot bolt paste -G 052 112 A3 -; hot bolt paste must not get into the slot of the probe body |
17 - | Connector |
q | 4-pin |
q | for lambda probe downstream of catalytic converter -G130- |
q | Brown |
q | Fitting location → Chapter |
18 - | Coolant temperature sender -G62- |
q | before removing, reduce pressure in cooling system if necessary |
19 - | O-ring |
q | replace |
20 - | Retaining clip |
q | check tightness |
21 - | 8 Nm |
22 - | Coolant regulator housing |
q | disassembling and assembling → Chapter |
23 - | Retaining clip |
q | check tightness |
24 - | 81- and 40-pin plugs |
q | for control unit Simos -J361- |
q | only insert or remove plug when the ignition is switched off |
q | unlock the multi-pin plug connection before pulling out |
25 - | Engine control unit |
q | Fitting location → Chapter |
q | Check supply voltage → Current flow diagrams and Fitting locations |
q | replace → Chapter |
q | Coding → Vehicle diagnosis, testing and information system VAS 5051 |
26 - | Support |
27 - | 2 Nm |