Octavia Mk1
|
| 1 - | Brake servo unit |
| t | with master brake cylinder and brake fluid reservoir |
| t | Remove and install brake servo unit → Chapter |
| 2 - | Brake pressure sender -1--G201-1) |
| t | removing and installing → Chapter |
| 3 - | Lateral acceleration sender -G200-1) |
| t | Fitting location: next to the steering column under the dash panel |
| 4 - | Yaw rate sender -G202-1) |
| t | Fitting location: next to the steering column under the dash panel |
| 5 - | Steering angle sender -G85-1) |
| t | Fitting location: on the steering column between the steering wheel and the steering column switch |
| 6 - | ABS warning light -K47- |
| t | Fitting location: in the dash panel insert |
| t | function → Chapter |
| 7 - | Hand brake/brake fluid level warning light -K14/33- |
| t | Fitting location: in the dash panel insert |
| t | function → Chapter |
| 8 - | ESP warning light -K155- |
| t | Fitting location: in the dash panel insert |
| t | function → Chapter |
| 9 - | Parts of ABS system on rear axle |
| t | Rear right and rear left wheel speed sensors -G44/G46-1) |
| – | removing and installing → Chapter |
| – | Installing wheel speed sensor cables → Chapter |
| t | Pulse rotor for the wheel speed sensor at the rear on the right and left |
| – | check → Chapter |
| – | removing and installing: The pulse rotor must be changed together with the wheel hub → Chapter and → Chapter |
| 10 - | Brake vacuum pump -V192-1) |
| t | only on vehicles with automatic gearbox in combination with EU-4 engines |
| t | Fitting location: on the left of the assembly carrier |
| t | is checked by self-diagnosis in the engine control unit → Engine, Fuel Injection and Ignition System; Rep. gr.01 |
| t | removing and installing → Chapter |
| 11 - | Diagnostic connection |
| t | Fitting location: in the storage compartment on the driver's side |
| 12 - | Brake light switch -F-1) |
| t | is open in off position |
| – | adjust → Chapter |
| – | remove by turning 90° to the left → Chapter |
| – | install by turning 90° to the right → Chapter |
| t | must be tested in the measured value block 003 → Chapter |
| 13 - | Control unit for ABS/EDL/ESP -J104- |
| t | Fitting location: at the hydraulic unit in left of engine compartment |
| t | is checked by self-diagnosis |
| t | Check the multi-pin plug connection to the control unit → Chapter |
| t | Do not disconnect the multi-pin plug connection before the self-diagnosis is complete. switch off the ignition before disconnecting the plug connector. |
| 14 - | Hydraulic unit for ABS/EDL/ESP -N55-1) |
| t | Fitting position: left of engine compartment |
| t | the hydraulic unit -N55- consists of the hydraulic pump -V64- and the valve block with the inlet and exhaust valves |
| t | when changing, absolutely close the old part with a plug from the mounting part kit; SP no. → Electronic Catalogue of Original Parts |
| t | Remove and install hydraulic control unit (hydraulic unit -N55- with control unit -J104- → Chapter |
| t | Do not separate the hydraulic pump -V64- from the valve block. |
| t | Repairing the hydraulic control unit → Chapter |
| 15 - | Parts of ABS system on front axle |
| t | Front right and front left wheel speed sensors -G45/G47-1) |
| – | removing and installing → Chapter |
| – | Installing wheel speed sensor cables → Chapter |
| t | Pulse rotor for the wheel speed sensor at the front on the right and left |
| – | check → Chapter |
| – | removing and installing: The pulse rotor must be changed together with the wheel hub → Chapter |
| 16 - | Longitudinal acceleration sender -G251-1) |
| t | Fitting location: on the central pipe to the right, near the right pillar -A- |
| t | removing and installing → Chapter |
