Yeti
| Electrical/electronic components and fitting locations ABS Mark 60 EC (ABS/EDL/TCS/ESP) - up to CW 21/2010 |
| 1 - | ABS control unit -J104- |
| q | Fitting location for left-hand drive: at hydraulic unit in right of engine compartment |
| q | Fitting location for right-hand drive: at hydraulic unit in left of engine compartment |
| q | with integrated sensor unit for ESP -G419- |
| q | check → Vehicle diagnostic tester |
| q | do not disconnect the plug connector before the self-diagnosis is complete. switch off the ignition before disconnecting the plug connector. |
| q | The ABS control unit -J104- and the ABS hydraulic unit -N55- must not be separated from each other |
| q | Removing and installing control unit and hydraulic unit - Vehicles with left-hand drive → Chapter |
| q | Removing and installing control unit and hydraulic unit - Vehicles with right-hand drive → Chapter |
| 2 - | Hydraulic unit for ABS -N55- |
| q | Fitting location for left-hand drive: at hydraulic unit in right of engine compartment |
| q | Fitting location for right-hand drive: at hydraulic unit in left of engine compartment |
| The hydraulic unit consists of these components: |
| q | ABS hydraulic pump -V64- |
| q | Brake pressure sender 1 -G201- |
| q | check → Vehicle diagnostic tester |
| q | Valve block, (includes the inlet and exhaust valves) |
| q | The ABS control unit -J104- and the ABS hydraulic unit -N55- must not be separated from each other |
| q | The hydraulic pump -V64- and the ABS hydraulic unit -N55- must not be separated from each other |
| q | Removing and installing control unit and hydraulic unit - Vehicles with left-hand drive → Chapter |
| q | Removing and installing control unit and hydraulic unit - Vehicles with right-hand drive → Chapter |
| 3 - | ABS warning light -K47- |
| q | Operation: → Chapter |
| 4 - | ESP and TCS warning light -K155- |
| q | Operation: → Chapter |
| 5 - | Dual circuit and hand brake system warning light -K7- |
| q | Operation: → Chapter |
| 6 - | Brake pad warning light -K32- |
| q | Operation: → Chapter |
| 7 - | Warning light for tyre pressure display -K220- |
| q | Operation: → Chapter |
| 8 - | Warning light for Downhill Drive Support -K250- |
| q | Operation: → Chapter |
| 9 - | Brake light switch -F- and brake pedal switch -F47- |
| q | Fitting location: on master brake cylinder |
| q | removing and installing → Chapter |
| q | check → Vehicle diagnostic tester |
| 10 - | TCS and ESP button -E256- |
| q | Fitting location: in the centre console |
| 11 - | Button for Downhill Drive Support |
| q | Fitting location: in the centre console |
| 12 - | Button for tyre pressure inspection -E226- |
| q | Fitting location: in the centre console |
| 13 - | Diagnostic connection |
| q | Fitting location: (left) in the footwell on the driver's side |
| 14 - | Rear right and left wheel speed sensors -G44-/-G46- (vehicles with four-wheel drive) |
| q | check → Vehicle diagnostic tester |
| q | removing and installing → Chapter |
| 15 - | Wheel-bearing housing - rear axle (vehicles with four-wheel drive) |
| 16 - | Wheel hub with wheel bearing (vehicles with four-wheel drive) |
| q | Sensor ring for ABS is built into the wheel hub |
| 17 - | Wheel-bearing housing - rear axle (vehicles with front-wheel drive) |
| 18 - | Wheel hub with wheel bearing (vehicles with front-wheel drive) |
| q | Sensor ring for ABS is built into the wheel hub |
| 19 - | Rear right and left wheel speed sensors -G44-/-G46- (vehicles with front-wheel drive) |
| q | check → Vehicle diagnostic tester |
| q | removing and installing → Chapter |
| 20 - | Wheel hub with wheel bearing - front axle |
| q | Sensor ring for ABS is built into the wheel hub |
| 21 - | Wheel-bearing housing - front axle |
| 22 - | Front right and left wheel speed sensors -G45-/-G47- |
| q | check → Vehicle diagnostic tester |
| q | removing and installing → Chapter |
| 23 - | Steering angle sender -G85- |
| q | the steering angle sender is installed in the steering gear and cannot be replaced separately |
| q | check → Vehicle diagnostic tester |
