Outback F6-3.0L DOHC (2006)
4. SYSTEM CALIBRATION
CAUTION:
-
When a trouble is occurred during the system calibration resulting in interruption of sensor data output, the DTC 28 {Adjustment/Inspection
halt} of occupant detection system will be detected to illuminate the airbag warning light.
In this case, perform the system calibration again, or perform the system calibration again after repairing the trouble cause.
-
Compartment temperature during the system calibration must be within 0 - 40 degree C.
1. Park the vehicle on a level surface.
2. Unload the cargo and set the vehicle in curb weight condition.
3. Connect the Subaru Select Monitor to vehicle, and then turn the ignition switch to ON.
4. Turn the Subaru Select Monitor switch to ON.
5. On the "Main Menu" display screen, select the {Each System Check} and press the [YES] key.
6. On the "System Selection Menu" display screen, select the {Occupant Sensing System} and press the [YES] key.
7. After the {2005 LOAD CELL TYPE OCCUPANT DETECTION SYSTEM Press the [YES] key} is displayed, check the model year and
press the [YES] key.
8. On the {OCCUPANT DETECTION SYSTEM} display screen, select the {1.System Calibration} and press the [YES] key.
9. When the {Complete all calibration checks, illuminated and a trouble code saved. Continue: "YES", Quit: "NO"} is displayed, press the [YES]
key.
10. When the {Diagnostic code check No trouble Continue: "YES", Quit: "NO"} is displayed, press the [YES] key.
NOTE: When a DTC is detected, {Diagnostic code check some troubles occur See service manual Press "YES" to END} is displayed.
Inspect the DTC, and perform the calibration again after repairing trouble cause.
11. When the {Empty the passenger seat Continue: "YES", Quit: "NO"} is displayed, empty the passenger's seat and press the [YES] key.
12. When the {Adjust the passenger seat to the condition shown in Service manual Continue: "YES", Quit: "NO"} is displayed, slide the
passenger's seat to the rear most and lock it securely, and lock the backrest in the fore most securely, then press the [YES] key. (For the model
with power seat, operate the slide switch or reclining switch fully until no longer moved.)
NOTE:
-
After pressing the [YES] key, "Now processing...Wait for a while. Do not touch or give impact to vehicle and seat" is displayed. Do not
touch the vehicle within 20 seconds while the message is displayed.
-
When the {System calibration is unsuccessful See service manual Press "YES" to END} is displayed, go to step 19.
13. When the {Threshold adjustment Is successfully completed weight inspection in service manual continue: "YES", Quit: "NO"} is displayed,
press the [YES] key.
14. When the {Empty the passenger seat Continue: "YES", Quit: "NO"} is displayed, make sure the passenger's seat is empty and press the [YES]
key.
15. When the {Adjust the passenger seat to the condition shown with service manual Continue: "YES", Quit: "NO"} is displayed, check the seat
position and press the [YES] key.
NOTE:
-
Slide the seat to the rear most position and lock it securely. Lock the backrest securely in the front most position. (For the model with
power seat, operate the slide switch or reclining switch fully until no longer moved.)
-
Diagnostic trouble code (DTC) is input when selecting the "NO" in this step.
-
After pressing the [YES] key, "Now processing...Wait for a while. Do not touch or give impact to vehicle and seat" is displayed. Do not
touch the vehicle within 20 seconds while the message is displayed.
-
When the {System calibration is unsuccessful See service manual Press "YES" to END} is displayed, go to step 19.
16. {input threshold weight mass lbs) [00.0] Press "YES" After inputting weight mass} is displayed. Input the weight amount (79.1 lbs) and press
the [YES] key.
