4 Runner 4WD V8-4.7L (2UZ-FE) (2003)
/Page-928003.png)
5. When the solenoids are OFF, check that the brake pedal can be depressed. If the pedal cannot be depressed, replace the brake master
cylinder.
6. Once, release the brake pedal. After depressing and holding the brake pedal with stable force, turn the SFLH and SFLR solenoids ON
simultaneously.
HINT: To protect the solenoids, hand-held tester turns OFF automatically 2 sec. after every solenoid has been turned ON.
7. When the solenoids are OFF, check that the brake pedal can be depressed. If the pedal cannot be depressed, replace the brake master
cylinder.
h. Jack up and support the vehicle.
i.
Release the parking brake pedal.
j.
Shift the transfer shift lever to "N" position and check that the rear wheels by rotating them by hand.
k. Inspect the rear TRAC & VSC solenoid operation.
1. Select the "SA3" and "STR" on the hand-held tester.
2. Turn the "SA3" and "STR" ON simultaneously with the hand-held tester, and check that the rear wheel does not rotate by hand.
HINT: When rotating the wheel fast, the fail-safe function is activated and judgement cannot be made properly. So rotate the wheel as
slowly as possible. If the rear wheels rotate, replace the brake master cylinder.
3. Turn the "SA3" and "STR" OFF simultaneously, and check that the rear wheels by rotating them by hand.
HINT:
^
To protect the solenoids, hand-held tester turns OFF automatically 2 sec. after every solenoid has been turned ON.
^
When rotating the wheel fast, the fail-safe function is activated and judgement cannot be made properly. So rotate the wheel as slowly
as possible.
NOTICE: When operating it continuously, set the interval of more than 20 sec. If the rear wheels stop, replace the brake master cylinder.
l.
Inspect the right rear ABS solenoid.
1. Select the "SA3", "STR" and "SRRH", on the hand-held tester.
2. Turn the "SA3", "STR" and "SRRH" ON simultaneously with the hand-held tester, and check that the right rear wheel by rotating it by
hand.
HINT:
^
To protect the solenoids, hand-held tester turns OFF automatically 2 sec. after every solenoid has been turned ON.
^
When rotating the wheel fast, the fail-safe function is activated and judgement cannot be made properly. So rotate the wheel as slowly
as possible.
^
When solenoid is OFF, the wheel might stop temporarily. However if the wheel rotates again, the function works normally. If the rear
wheels stop, replace the brake master cylinder.
3. Turn the "SA3", "STR" and "SRRH" OFF, and check that the right rear wheel by rotating it by hand.
HINT:
^
To protect the solenoids, hand-held tester turns OFF automatically 2 sec. after every solenoid has been turned ON.
^
When rotating the wheel fast, the fail-safe function is activated and judgement cannot be made properly. So rotate the wheel as slowly
as possible. If the right rear wheel stop, replace the brake master cylinder.
4. Depress the pedal with stable force, then turn the "SRRH" and "SRRR" ON simultaneously.
5. When the solenoids are ON, check that the right rear wheel by rotating it by hand.
m. Inspect the left rear ABS solenoid operation.
1. Select the "SA3", "STR" and "SRLH" on the hand-held tester.
2. Turn the "SA3", "STR" and "SRLH" ON with hand-held tester, and check that the left rear wheel by rotating it by hand.
HINT: When rotating the wheel fast, the fail-safe function is activated and judgement cannot be made properly. So rotate the wheel as
slowly as possible. If the rear wheels stop, replace the brake master cylinder.
3. Turn the "SA3", "STR" and "SRLH" OFF and check that the left rear wheel by rotating it by hand.
HINT:
^
To protect the solenoids, hand-held tester turns OFF automatically 2 sec. after every solenoid has been turned ON.
^
When rotating the wheel fast, the fail-safe function is activated and judgement cannot be made properly. So rotate the wheel as slowly
as possible.
^
When solenoid is OFF, the wheel might stop temporarily. However if the wheel rotates again, the function works normally. If the left
rear wheel stop, replace the brake master cylinder.
