Camry L4-2.4L (2AZ-FXE) Hybrid (2007)
9. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH See: Body and Frame/Interior Moulding / Trim/Headliner/Service and Repair/Roof
Headlining/Removal
10. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL LH See: Body and Frame/Interior Moulding / Trim/Dashboard / Instrument
Panel/Service and Repair/Removal and Replacement/Instrument Panel Safety Pad (for TMC Made)(From 10-2006)/Removal
11. REMOVE INSTRUMENT PANEL NO. 2 UNDER COVER SUB-ASSEMBLY See: Body and Frame/Interior Moulding / Trim/Dashboard /
Instrument Panel/Service and Repair/Removal and Replacement/Instrument Panel Safety Pad (for TMC Made)(From 10-2006)/Removal
12. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY See: Body and Frame/Interior Moulding / Trim/Dashboard / Instrument
Panel/Service and Repair/Removal and Replacement/Instrument Panel Safety Pad (for TMC Made)(From 10-2006)/Removal
13. REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY See: Body and Frame/Interior Moulding / Trim/Dashboard / Instrument
Panel/Service and Repair/Removal and Replacement/Instrument Panel Safety Pad (for TMC Made)(From 10-2006)/Removal
14. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY See: Body and Frame/Interior Moulding / Trim/Dashboard / Instrument Panel/Service
and Repair/Removal and Replacement/Instrument Panel Safety Pad (for TMC Made)(From 10-2006)/Removal
15. REMOVE CONSOLE BOX POCKET See: Body and Frame/Interior Moulding / Trim/Dashboard / Instrument Panel/Service and Repair/Removal
and Replacement/Instrument Panel Safety Pad (for TMC Made)(From 10-2006)/Removal
16. REMOVE CONSOLE BOX CARPET See: Body and Frame/Interior Moulding / Trim/Dashboard / Instrument Panel/Service and Repair/Removal
and Replacement/Instrument Panel Safety Pad (for TMC Made)(From 10-2006)/Removal
17. REMOVE CONSOLE BOX ASSEMBLY See: Body and Frame/Interior Moulding / Trim/Dashboard / Instrument Panel/Service and
Repair/Removal and Replacement/Instrument Panel Safety Pad (for TMC Made)(From 10-2006)/Removal
18. REMOVE NO. 2 CONSOLE BOX INSERT FRONT See: Body and Frame/Interior Moulding / Trim/Dashboard / Instrument Panel/Service and
Repair/Removal and Replacement/Instrument Panel Safety Pad (for TMC Made)(From 10-2006)/Removal
19. REMOVE NO. 1 CONSOLE BOX INSERT FRONT See: Body and Frame/Interior Moulding / Trim/Dashboard / Instrument Panel/Service and
Repair/Removal and Replacement/Instrument Panel Safety Pad (for TMC Made)(From 10-2006)/Removal
20. REMOVE NO. 1 CONSOLE BOX DUCT See: Heating and Air Conditioning/Housing Assembly HVAC/Service and Repair/Removal and
Replacement/Air Conditioning Unit (for TMC Made)/Removal
21. REMOVE YAW RATE AND ACCELERATION SENSOR
(a) Disconnect the yaw rate and acceleration sensor connector.
(b) Remove the 2 bolts and yaw rate and acceleration sensor.
NOTICE: Do not remove the yaw rate and acceleration sensor from the bracket.
Installation
BRAKE CONTROL: YAW RATE AND ACCELERATION SENSOR (for TMC Made): INSTALLATION
INSTALLATION
1. INSTALL YAW RATE AND ACCELERATION SENSOR
(a) Install the yaw rate and acceleration sensor with the 2 bolts.
Torque: 13 Nm (133 kgf-cm, 10ft-lbf)
NOTICE:
-
Do not damage the yaw rate and acceleration sensor.
-
Make sure that the yaw rate and acceleration sensor is installed securely.
(b) Connect the yaw rate and acceleration sensor connector.