Prius L4-1.8L (2ZR-FXE) Hybrid (2010)
without SST - Torque : 18 Nm (178 kgf-cm, 13 ft-lbf)
with SST - Torque : 11 Nm (112 kgf-cm, 8 ft-lbf)
NOTICE:
*
Use a torque wrench with a fulcrum length of 250 mm (9.84 in.).
*
This torque value is effective when SST is parallel to a torque wrench.
*
If the center airbag sensor assembly has been dropped, or there are any cracks, dents or other defects in the case or connector,
replace it with a new one.
*
When installing the center airbag sensor assembly, be careful that the SRS wiring does not interfere with or is not pinched
between other parts.
*
When the power switch is first turned on (IG) after the center airbag sensor assembly has been replaced, make sure that no one is
in the vehicle.
(d) Connect the connectors to the center airbag sensor assembly as shown in the illustration.
NOTICE:
When connecting any airbag connector, take care not to damage the airbag wire harness.
(e) Check that the waterproof sheet is properly set.
(f) Check that there is no looseness in the installation parts of the center airbag sensor assembly.
2. INSTALL UPPER INSTRUMENT PANEL FINISH PANEL ASSEMBLY See: Body and Frame/Interior Moulding / Trim/Dashboard /
Instrument Panel/Service and Repair/Removal and Replacement/Lower Instrument Panel/Installation
3. INSTALL CONSOLE BOX ASSEMBLY See: Body and Frame/Interior Moulding / Trim/Dashboard / Instrument Panel/Service and
Repair/Removal and Replacement/Lower Instrument Panel/Installation
4. INSTALL BOX BOTTOM MAT See: Body and Frame/Interior Moulding / Trim/Dashboard / Instrument Panel/Service and Repair/Removal and
Replacement/Lower Instrument Panel/Installation
5. INSTALL FRONT NO. 2 CONSOLE BOX INSERT See: Body and Frame/Interior Moulding / Trim/Dashboard / Instrument Panel/Service and
Repair/Removal and Replacement/Lower Instrument Panel/Installation
6. INSTALL FRONT NO. 1 CONSOLE BOX INSERT See: Body and Frame/Interior Moulding / Trim/Dashboard / Instrument Panel/Service and
Repair/Removal and Replacement/Lower Instrument Panel/Installation
7. INSTALL NO. 2 CONSOLE BOX MOUNTING BRACKET See: Body and Frame/Interior Moulding / Trim/Dashboard / Instrument
Panel/Service and Repair/Removal and Replacement/Lower Instrument Panel/Installation
8. INSTALL ELECTRICAL KEY OSCILLATOR See: Accessories and Optional Equipment/Antitheft and Alarm Systems/Keyless Entry/Antenna -
Keyless Entry/Service and Repair/Electrical Key Oscillator (for Front Floor)/Installation
9. INSTALL SHIFT LOCK CONTROL UNIT ASSEMBLY See: Transmission and Drivetrain/Continuously Variable
Transmission/Transaxle/Shifter CVT/Service and Repair/Installation
10. INSTALL AIR CONDITIONING CONTROL ASSEMBLY See: Heating and Air Conditioning/Control Assembly/Service and
Repair/Installation
11. INSTALL GLOVE COMPARTMENT DOOR See: Body and Frame/Interior Moulding / Trim/Dashboard / Instrument Panel/Service and
Repair/Removal and Replacement/Upper Instrument Panel/Installation
12. INSTALL NO. 2 INSTRUMENT PANEL REGISTER See: Body and Frame/Interior Moulding / Trim/Dashboard / Instrument Panel/Service
and Repair/Removal and Replacement/Upper Instrument Panel/Installation
13. INSTALL NO. 1 SIDE DEFROSTER NOZZLE See: Body and Frame/Interior Moulding / Trim/Dashboard / Instrument Panel/Service and
Repair/Removal and Replacement/Upper Instrument Panel/Installation
14. INSTALL RADIO RECEIVER WITH BRACKET (w/o Navigation System) See: Accessories and Optional Equipment/Radio, Stereo, and
Compact Disc/Radio/Stereo/Service and Repair/Radio Receiver/Installation
15. INSTALL NAVIGATION RECEIVER WITH BRACKET (w/ Navigation System) See: Accessories and Optional Equipment/Navigation
System/Service and Repair/Installation
16. INSTALL UPPER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY See: Body and Frame/Interior Moulding / Trim/Dashboard /