Sequoia 4WD V8-5.7L (3UR-FE) (2009)
HINT: Use the same procedure as for the RH side.
Installation
SUPPLEMENTAL RESTRAINT SYSTEMS: REAR AIRBAG SENSOR: INSTALLATION
INSTALLATION
1. INSTALL REAR AIRBAG SENSOR RH
(a) Check that the ignition switch is off.
(b) Check that the battery negative (-) terminal is disconnected.
CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(c) Engage the guide and Install the rear airbag sensor.
(d) Install the bolt.
Torque: 9.0 Nm (92 kgf-cm, 80 in-lbf)
CAUTION:
-
If the rear airbag sensor LH has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector,
replace it with a new one.
-
When installing the rear airbag sensor LH, be careful that the SRS wiring does not interfere with other parts and that it is not
pinched between other parts.
(e) Check that there is no looseness in the installation parts of the rear airbag sensor.
(f) Connect the connector to the rear airbag sensor.
2. INSTALL REAR AIRBAG SENSOR LH
HINT: Use the same procedure as for the RH side.
3. INSTALL REAR SIDE NO. 3 AIR DUCT See: Heating and Air Conditioning/Housing Assembly HVAC/Service and Repair/Rear Air
Conditioning Unit/Installation
4. INSTALL QUARTER TRIM PANEL ASSEMBLY RH (for Standard) See: Body and Frame/Interior Moulding / Trim/Headliner/Service and
Repair/Installation
5. INSTALL QUARTER TRIM PANEL ASSEMBLY LH (for Standard) See: Body and Frame/Interior Moulding / Trim/Headliner/Service and
Repair/Installation
6. INSTALL QUARTER TRIM PANEL ASSEMBLY RH (for Power Seat) See: Body and Frame/Interior Moulding / Trim/Headliner/Service and
Repair/Installation
7. INSTALL QUARTER TRIM PANEL ASSEMBLY LH (for Power Seat) See: Body and Frame/Interior Moulding / Trim/Headliner/Service and
Repair/Installation
8. INSTALL REAR FLOOR MAT SUPPORT PLATE See: Body and Frame/Interior Moulding / Trim/Headliner/Service and Repair/Installation
9. INSTALL ROPE HOOK ASSEMBLY See: Body and Frame/Interior Moulding / Trim/Headliner/Service and Repair/Installation
10. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH See: Body and Frame/Interior Moulding / Trim/Headliner/Service and
Repair/Installation
11. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH See: Body and Frame/Interior Moulding / Trim/Headliner/Service and
Repair/Installation
12. INSTALL REAR DOOR SCUFF PLATE RH See: Body and Frame/Interior Moulding / Trim/Headliner/Service and Repair/Installation
13. INSTALL REAR DOOR SCUFF PLATE LH See: Body and Frame/Interior Moulding / Trim/Headliner/Service and Repair/Installation
14. INSTALL REAR FLOOR STEP NO. 1 COVER See: Body and Frame/Interior Moulding / Trim/Headliner/Service and Repair/Installation
15. INSTALL REAR FLOOR STEP NO. 2 COVER See: Body and Frame/Interior Moulding / Trim/Headliner/Service and Repair/Installation
16. INSTALL REAR SEAT CUSHION HINGE LOWER COVER RH See: Body and Frame/Interior Moulding / Trim/Headliner/Service and
Repair/Installation
17. INSTALL REAR SEAT CUSHION HINGE LOWER COVER LH See: Body and Frame/Interior Moulding / Trim/Headliner/Service and
Repair/Installation
18. INSTALL REAR NO. 2 SEAT ASSEMBLY RH