Sienna AWD V6-3.3L (3MZ-FE) (2004)
/Page-320009.png)
NOTICE:
^
Remove any oil from the contact surface.
^
Install the cylinder head cover within 3 minutes after applying seal packing.
^
Do not start the engine within 2 hours after installing.
b. Install the cylinder head cover with the 9 bolts. Tighten the bolt uniformly in several steps.
Torque: 8.0 Nm (80 kgf-cm, 71 inch lbs.)
c. Install the engine wire harness with the 3 nuts.
Torque: 8.4 Nm (85 kgf-cm, 74 inch lbs.)
21. INSTALL CYLINDER HEAD COVER SUB-ASSY LH
a. Apply seal packing to the cylinder head as shown in the illustration.
Seal packing: Part No. 08826-00080 or equivalent
NOTICE:
^
Remove any oil from the contact surface.
^
Install the cylinder head cover within 3 minutes after applying seal packing.
^
Do not start the engine within 2 hours after installing.
b. Install the cylinder head cover with the 9 bolts. Tighten the bolt uniformly in several steps.
Torque: 8.0 Nm (80 kgf-cm, 71 inch lbs.)
c. Using an E6 torx socket wrench, install the engine wire harness protector with the 2 bolts.
Torque: 8.4 Nm (85 kgf-cm, 74 inch lbs.)
22. INSTALL IGNITION COIL ASSY
Torque: 8.0 Nm (80 kgf-cm, 71 inch lbs.)
23. INSTALL INTAKE AIR SURGE TANK
a. Install a new gasket to the intake air surge tank.
b. Install the intake air surge tank and the emission control valve bracket with the 2 nuts.
Torque: 28 Nm (286 kgf-cm, 21 ft. lbs.)
c. Using a socket hexagon wrench 8, tighten the 4 bolts.
Torque: 28 Nm (286 kgf-cm, 21 ft. lbs.)
d. Install the surge tank stay No. 2 with the 2 bolts.
Torque: 20 Nm (199 kgf-cm, 14 ft. lbs.)
e. Install the surge tank stay No. 1 with the 2 bolts.
Torque: 20 Nm (199 kgf-cm, 14 ft. lbs.)
f.
Install the engine hunger No. 1 with the 2 bolts.
Torque: 20 Nm (199 kgf-cm, 14 ft. lbs.)
g. Install the pressure feed tube with the 2 nuts.
Torque: 7.8 Nm (80 kgf-cm, 69 inch lbs.)
h. Connect the ventilation hose.
i.
Connect the union to check valve hose.
j.
Connect the water by-pass hose No. 2.
k. Connect the water by-pass hose No. 3.
l.
Connect the throttle motor connector.
24. INSTALL EMISSION CONTROL VALVE SET
Torque: 8.0 Nm (82 kgf-cm, 71 inch lbs.)
25. INSTALL AIR CLEANER CAP SUB-ASSY
26. CONNECT VACUUM HOSE
27. INSTALL V-BANK COVER SUB-ASSY
a. Fit the 2 retainers and install the V-bank cover.
b. Using a socket hexagon wrench 5, tighten the 3 nuts.
Torque: 7.9 Nm (81 kgf-cm, 70 inch lbs.)
28. INSTALL COWL TOP PANEL SUB-ASSY OUTER FRONT
29. INSTALL COWL TOP TO COWL BRACE INNER NO.1
