Sienna FWD V6-3.5L (2GR-FE) (2009)
SST: 09023-00101
23. CONNECT REAR BRAKE TUBE NO.1
SST: 09023-00101
HINT: Connect the RH side by the same procedures as the LH side.
24. INSTALL PARKING BRAKE CABLE ASSEMBLY NO.3
HINT: See: Suspension Spring ( Coil / Leaf )/Service and Repair/Removal and Replacement/Rear Coil Spring/Components
25. INSTALL PARKING BRAKE CABLE ASSEMBLY NO.2
HINT: Install the RH side by the same procedures as the LH side.
26. INSTALL DIFFERENTIAL CARRIER ASSEMBLY REAR (for 4WD)
HINT:
27. INSTALL REAR DRIVE SHAFT ASSEMBLY LH (for 4WD)
HINT: See: Wheel Hub/Service and Repair/Removal and Replacement/Rear Axle Hub and Bearing/Components
28. INSTALL REAR DRIVE SHAFT ASSEMBLY RH (for 4WD)
HINT: Install the RH side by the same procedures as the LH side.
29. INSTALL REAR AXLE SHAFT LH NUT (for 4WD)
HINT: See: Wheel Hub/Service and Repair/Removal and Replacement/Rear Axle Hub and Bearing/Components
30. INSTALL REAR AXLE SHAFT RH NUT (for 4WD)
HINT: Install the RH side by the same procedures as the LH side.
31. INSTALL PROPELLER W/CENTER BEARING SHAFT ASSEMBLY (for 4WD)
32. CONNECT SKID CONTROL SENSOR WIRE (for 2WD)
HINT: See: Suspension Spring ( Coil / Leaf )/Service and Repair/Removal and Replacement/Rear Coil Spring/Components
HINT: Connect the RH side by the same procedures as the LH side.
33. INSTALL SPEED SENSOR REAR LH (for 4WD)
HINT: See: Suspension Spring ( Coil / Leaf )/Service and Repair/Removal and Replacement/Rear Coil Spring/Components
34. INSTALL SPEED SENSOR REAR RH (for 4WD)
HINT: Install the RH side by the same procedures as the LH side.
35. INSTALL EXHAUST PIPE ASSEMBLY TAIL
HINT:
-
2WD DRIVE TYPE See: Engine, Cooling and Exhaust/Exhaust System/Exhaust Pipe/Service and Repair/Removal
-
4WD DRIVE TYPE See: Engine, Cooling and Exhaust/Exhaust System/Exhaust Pipe/Service and Repair/Removal
36. BLEED BRAKE LINE
HINT: See: Brakes and Traction Control/Brake Bleeding/Service and Repair
37. INSTALL REAR WHEEL
Torque: 103 Nm (1,050 kgf-cm, 76ft-lbf)
38. INSPECT BRAKE FLUID LEVEL IN RESERVOIR
39. STABILIZE SUSPENSION
HINT: See: Suspension Strut / Shock Absorber/Service and Repair/Removal and Replacement/Rear Shock Absorber/Installation
40. FULLY TIGHTEN SHOCK ABSORBER ASSEMBLY REAR LH
HINT: See: Suspension Strut / Shock Absorber/Service and Repair/Removal and Replacement/Rear Shock Absorber/Installation
41. FULLY TIGHTEN SHOCK ABSORBER ASSEMBLY REAR RH
HINT: Fully tighten the RH side by the same procedures as the LH side.
42. FULLY TIGHTEN REAR AXLE BEAM ASSEMBLY
HINT: See: Suspension Spring ( Coil / Leaf )/Service and Repair/Removal and Replacement/Rear Coil Spring/Components
43. INSTALL REAR FLOOR NO.2 CROSSMEMBER BRACE LH
HINT: See: Suspension Spring ( Coil / Leaf )/Service and Repair/Removal and Replacement/Rear Coil Spring/Components
44. INSTALL REAR FLOOR NO.2 CROSSMEMBER BRACE RH
HINT: Install the RH side by the same procedures as the LH side.