Recommended Torque Values
|
Nm |
Adapter to oil pump (C 20 XE) |
23 1) |
DIS ignition module to cylinder head (M10) |
30 |
DIS ignition module to cylinder head (M8) |
20 |
Starter to transmission housing |
75 |
Starter to cylinder block |
45 |
Drive disc to crankshaft |
60 2) |
Exhaust manifold to cylinder head |
22 3) |
Fuel pressure regulator fastening clip |
5 |
DIS ignition module to adapter |
8 |
Torsional vibration damper to toothed belt drive gear |
20 |
1) Regroove thread before reuse and insert screws with screw lock (red). 2) Use new fastening bolt(s). 3) Use new fastening bolt(s).
Recommended Torque Values (continued)
|
Nm |
Throttle body to intake manifold |
9 |
Intake manifold to cylinder head |
22 1) |
Performance header to cylinder head (C 20 XE) |
22 1) |
Engine ventilation flange to cylinder block |
25 |
Crankshaft pulse pick-up sensor disc to crankshaft |
13 2) |
Camshaft sensor disk to camshaft (C 20 XE) |
8 |
Camshaft sensor housing to cylinder head (C 20 XE) |
15 |
Transmission to cylinder block |
60 |
Auxiliary aggregates bracket to cylinder block |
35 |
Starter bracket to cylinder block |
25 |
1) Use new fastening nut(s). 2) Use new fastening bolt(s).
Recommended Torque Values (continued)
|
Nm |
Engine damping block bracket to auxiliary aggregates support |
60 |
Engine damping block bracket to engine holder |
60 |
Rear engine damping block bracket to transmission |
60 |
Front right engine damping block to bracket |
60 |
Compressor bracket to ancillary component bracket and cylinder block. |
35 |
Compressor bracket to compressor |
20 |
Toothed belt guide roller bracket to cylinder block |
25 |
Intermediate shaft bracket to cylinder block |
55 |
Rear toothed belt cover to oil pump and cylinder head |
6 |
Heat shield to exhaust manifold / performance header |
8 |
Recommended Torque Values (continued)
|
Nm |
High-voltage distributor to cylinder head (C 20 XE) |
15 |
Crankshaft pulse pick-up to cylinder block |
8 |
V-belt pulley to toothed belt drive gear |
20 |
Ribbed V-belt tension roller to ancillary components support |
25 |
Knock sensor to cylinder block |
20 |
Fuel distributor tube to intake manifold |
8 |
Fuel return line (1) and fuel flow line (2) to fuel distribution pipe or fuel pressure regulator. |
15 |
Coolant flange to cylinder head (M10) |
30 |
Coolant flange to cylinder head (M8) |
20 |
Coolant pump to cylinder block |
25 |
Recommended Torque Values (continued)
|
Nm |
Crankshaft bearing bridge to cylinder block |
20 + 45 ° 1) |
Crankshaft bearing cap to cylinder block |
50 + 45 ° +15 ° 1) |
Oxygen sensor in exhaust pipe |
30 |
Alternator shackle to alternator and intake manifold |
20 |
Shackle, power steering pump to auxiliary aggregates bracket |
18 |
Rear engine damping block to engine damping block bracket |
45 |
Engine damping block, rear to front axle body |
40 |
Front engine damping block to engine damping block bracket (M10) |
60 |
Front engine damping block to side member |
65 2) |
Camshaft sensor to camshaft sensor housing (C 20 XE) |
6 |
1) Use new fastening bolt(s). 2) Regroove thread and insert screws with screw lock (red).
Recommended Torque Values (continued)
|
Nm |
Rear camshaft bearing cover to cylinder head (M6) (C 20 XE) |
10 |
Camshaft bearing caps to cylinder head |
8 |
Camshaft bearing cover to cylinder head (M8) (C 20 XE) |
20 |
Camshaft pulley to camshaft |
50 + 60 ° + 15 ° 1) |
Camshaft sensor to cylinder head |
6 |
Oil drain plug (inner Torx screw) to oil pan |
10 |
Oil drain plug (hex screw) to oil pan |
45 |
Oil pressure switch to oil pump |
40 |
Oil filter to oil pump |
15 |
Oil cooler line to adapter and oil cooler (C 20 XE) |
30 |
Recommended Torque Values (continued)
|
Nm |
Oil pump to cylinder block |
8 |
Oil pump cover to oil pump |
6 |
Oil intake pipe to oil pump |
8 1) |
Intake pipe to cylinder block |
6 |
Oil baffle plate to crankshaft bearing bridge |
8 |
Oil pan to cylinder block and oil pump |
20 |
Upper part of oil pan to transmission |
40 |
Upper part of oil pan to cylinder block |
20 1) |
Lower part of oil pan to upper part of oil pan |
8 + 30 ° 1) 2) |
Con-rod bearing cap to con-rod |
35 + 45 ° + 15 ° 2) |
1) Regroove thread before reuse and insert screws with screw lock (red). 2) Use new fastening bolt(s).
Recommended Torque Values (Continued)
|
Nm |
Power steering pump to ancillary component bracket |
25 |
Flywheel to crankshaft |
65 + 30 ° + 15 ° 1) |
Coolant temperature sensor to DIS ignition module adapter |
10 |
Coolant temperature sensor to thermostat housing (C 20 XE) |
18 |
Intake manifold support to intake manifold and cylinder block |
25 |
Alternator support to alternator and intake manifold |
20 |
Thermostat housing to cylinder head |
15 |
Safety valve to oil pump |
30 |
Vacuum line, brake servo to intake manifold |
20 |
Lower generator fastening bolt |
35 |
1) Use new fastening bolt(s).
Recommended Torque Values (continued)
|
Nm |
Compressor to auxiliary aggregates bracket |
35 |
Temperature regulator screw plug to temperature regulator housing (C 20 XE) |
30 1) |
Front toothed belt cover to rear toothed belt cover |
6 |
Toothed belt drive gear to crankshaft |
130 + 45 °± 5 ° 2) |
Toothed belt tension roller to oil pump |
20 |
Toothed belt tension roller to cylinder block (C 20 XE) |
25 + 40 ° + 15 ° 2) |
Toothed belt guide roller to guide roller bracket |
25 |
Toothed belt guide roller to cylinder block |
25 |
Toothed belt guide roller to cylinder block (C 20 XE) |
25 + 40 ° + 15 ° 2) |
Ignition cable cover to cylinder head cover |
3 |
1) Use new screw plug. 2) Use new fastening bolt(s).
Recommended Torque Values (continued)
|
Nm |
Ignition cable cover to cylinder head housing (C 20 XE) |
8 |
Spark plug to cylinder head |
25 |
Cylinder head to cylinder block |
25 + 90 ° + 90 ° + 90 ° + 15 ° 1) 2) |
Cylinder head to cylinder block (C 20 XE) |
25 + 65 ° + 65 ° + 65 ° 1) 2) |
Cylinder head cover to cylinder head |
8 |
1) Use new fastening bolt(s). 2) additional tightening not required.
|