Recommended Torque Values
|
|
Nm |
|
Starter to transmission |
38 |
|
Connecting port, oil feed line to turbocharger |
41 |
|
Thermostat connection port to cylinder head |
30 |
|
Camshaft drive gear to camshaft |
14 |
|
Coolant pump pulley to coolant pump |
10 |
|
Exhaust manifold to cylinder head |
24 |
|
Exhaust pipe to turbocharger |
67 |
|
Thermostat housing cover to thermostat housing |
30 |
|
Intake manifold to cylinder head |
24 |
|
Injector nozzle to injector nozzle holder |
44 |
|
Injector nozzle holder to cylinder head |
50 |
|
Injection line to injection pump and injector nozzle holder |
25 |
Recommended Torque Values (continued)
|
|
Nm |
|
Injection pump to cylinder block |
23 |
|
Injection pump drive gear to injection pump |
69 |
|
Bleeder screw to injection pump |
20 |
|
Alternator to bracket (M8) |
24 |
|
Alternator to bracket (M10) |
48 |
|
Sheathed glow plugs to cylinder head |
20 |
|
Injection pump bracket to injection pump |
34 |
|
Injection pump bracket to cylinder block |
39 |
|
Alternator bracket to cylinder block |
24 |
|
Bracket, crankshaft rear seal ring to cylinder block |
10 |
|
Bracket, right engine mount to engine mount and cylinder block |
45 |
|
Power steering pump bracket to bracket (cylinder head) |
48 |
Recommended Torque Values (continued)
|
|
Nm |
|
Power steering pump bracket to cylinder head |
48 |
|
Accelerator pedal bracket to chassis |
20 |
|
Rear toothed belt cover to cylinder head and cylinder block |
10 |
|
Heat shield to exhaust manifold |
9 |
|
Clamp to shift linkage |
15 |
|
Fuel return line to injector nozzle holder |
29 |
|
Coolant line to turbocharger |
10 |
|
Coolant pump to cylinder block |
24 |
|
Coolant pipe to cylinder block |
95 |
|
Crankshaft bearing cap to cylinder block |
88 |
|
Charge air pipe to cylinder head |
20 |
|
Air intake hose to cylinder block |
18 |
|
Air cleaner to intake manifold |
8 |
Recommended Torque Values (continued)
|
|
Nm |
|
Engine damping block, rear, to bracket |
45 |
|
Engine damping block, rear, to crossmember |
40 |
|
Engine damping block, left, to bracket |
60 |
|
Engine damping block, left, to side member |
65 1) |
|
Engine damping block, right, to bracket |
35 |
|
Engine damping block, right, to side member |
65 1) |
|
Camshaft bearing caps to cylinder head. |
19 |
|
Oil drain bolt to oil pan |
78 |
|
Oil pressure valve to cylinder block |
40 |
|
Oil pressure switch to cylinder block |
21 |
|
Oil filter to oil cooler |
15 |
|
Oil cooler to cylinder block |
49 |
1) Cut back threads prior to reuse and apply screw locking (red) to fixing screws
Recommended Torque Values (continued)
|
|
Nm |
|
Oil cooler to cylinder block (banjo bolt) |
49 |
|
Oil line to vacuum pump |
25 |
|
Oil pump drive gear to oil pump |
44 |
|
Oil pump cover to cylinder block |
10 |
|
Oil pump intake pipe to cylinder block |
26 |
|
Oil baffle to cylinder block |
19 |
|
Oil feed line to cylinder block pipe connection |
28 |
|
Oil feed line to turbocharger |
20 |
|
Upper part of oil pan to cylinder block |
10 |
|
Lower part of oil pan to upper part of oil pan |
10 |
|
Con-rod bearing cap to con-rod |
25 + 100 ° to 115 ° 1) |
|
Crankshaft belt pulley to toothed belt drive wheel |
20 |
Recommended Torque Values (continued)
|
|
Nm |
|
Flywheel to crankshaft |
30 + 45 ° to 60 ° 1) |
|
Temperature sensor in thermostat housing |
8 |
|
Temperature switch in thermostat housing |
8 |
|
Thermostat housing to cylinder head |
24 |
|
Turbocharger to exhaust manifold |
27 |
|
Turbocharger support to cylinder block |
51 |
|
Safety valve to intake manifold |
49 |
|
Safety valve to cylinder block |
39 |
|
Vacuum pump to alternator |
7 |
|
Front axle body to chassis |
100 + 45 ° + 15 ° 1) |
|
Series resistor to intake manifold |
39 |
Recommended Torque Values (continued)
|
|
Nm |
|
Toothed belt drive gear to crankshaft |
196 |
|
Toothed belt tension roller to cylinder block |
19 |
|
Toothed belt guide roller to cylinder block |
80 |
|
Cylinder head to cylinder block |
40 + 60 ° to 75 ° + 60 ° to 75 ° 1) |
|
Cylinder head cover to cylinder head |
8 |
|
