Special Service Tools
|
KM-128-A |
Tester |
|
To check V-belt tension. |
|
KM-134-A |
Socket Wrench |
|
To remove and install cylinder head bolts |
|
KM-161-B |
Remover |
|
To remove toothed belt drive gear from crankshaft |
|
KM-232 |
Adapter |
|
To check engine oil pressure in conjunction with KM-498-B |
|
KM-301 |
Gauge Bar |
|
To measure piston and swirl chamber projection |
|
KM-340-1-E |
Cutter Set |
|
To cut and correct valve seating |
| 
|
Special-Tool (Continued)
|
KM-348 |
Valve spring compressor |
|
To compress valve springs in conjunction with KM-653 |
|
KM-352 |
Installer |
|
To insert valve stem seals |
|
KM-412 |
Engine Overhaul Stand |
|
To hold removed engine |
|
KM-412-11-A |
Adapter |
|
To hold engine in conjunction with KM-412 |
|
KM-470-B |
Angular Torque Wrench |
|
To tighten cylinder head bolts |
|
KM-471 |
Adapter |
|
Connection piece for cooling system tester |
| 
|
Special-Tool (Continued)
|
KM-498-B |
Fluid Pressure Gauge |
|
To check oil pressure in conjunction with KM-232 |
|
KM-517-B |
Locking Device |
|
To block flywheel (engine installed) |
|
KM-533-B |
Connector |
|
To check compression in conjunction with KM-649 |
|
MKM-571-B |
Dial Gauge |
|
Measurements in conjunction with KM-301 |
|
MKM-596-A |
Gauge |
|
To measure oil temperature |
|
MKM-604-C |
Torx Bit and Socket Set |
|
To remove/install Torx bolts |
| 
|
Special-Tool (Continued)
|
KM-609 |
Electronic-Kit I |
|
Diagnosis of electronic systems |
|
MKM-610 |
Torque Wrench, 1/2"" |
|
Measuring range 30 to 130 Nm/22 to 96 lbf. ft. |
|
MKM-611 |
Torque Wrench, 3/8"" |
|
Measuring range 10 to 60 Nm/7 to 44 lbf. ft. |
|
KM-649 |
Connector |
|
Test compression pressure in connection with KM-533-B |
|
KM-650-A |
Valve Compressor |
|
To adjust valve clearance |
|
KM-651-A |
Remover |
|
To remove injection pump impeller |
| 
|
Special-Tool (Continued)
|
KM-652 |
Flywheel Holder |
|
To lock the flywheel |
|
KM-653-A |
Adapter |
|
To compress valve springs in conjunction with KM-348 |
|
KM-654 |
Remover/Installer |
|
To remove and install valve guides |
|
KM-655 |
Installer |
|
To install oil spray nozzle (piston cooling) |
|
KM-656 |
Installer |
|
To install front crankshaft and camshaft seal rings |
|
KM-657 |
Installer |
|
To install oil pump seal ring in oil pump bracket |
| 
|
Special-Tool (Continued)
|
KM-658 |
Installer |
|
To install rear crankshaft seal ring in seal ring bracket |
|
KM-660 |
Installer |
|
To install front camshaft seal ring |
|
KM-662-C |
Holding Wrench |
|
To hold toothed belt drive gear when removing and installing fastening bolt |
|
MKM-667 |
Pressure and Vacuum Pump |
|
To measure charge pressure of turbocharger |
|
KM-668 |
Oil Filter Wrench |
|
To remove and install oil filter (ex works) |
|
KM-728-A |
Remover/Installer |
|
To install injector nozzles |
| 
|
Special-Tool (Continued)
|
KM-798 |
Dial Gauge |
|
To measure beginning of delivery |
|
KM-840 |
Remover |
|
To remove valve stem seals |
|
KM-845 |
Intake Device |
|
To remove flat valve lifters |
|
KM-849 |
Storage Facility |
|
Storage facility for pistons, con-rods and valves |
|
MKM-854 |
Oil Filter Wrench |
|
To remove and install oil filter (Service) |
|
MKM-883-1 |
Engine Bridge |
|
To hold/lift the engine |
| 
|
Special-Tool (Continued)
|
MKM-889 |
Valve Compressor |
|
To remove/install the valve stem seals (cylinder head installed) |
|
KM-898 |
Engine Transport Shackle |
|
To hold engine |
| 
|
|
