Vauxhall Workshop Service and Repair Manuals

Test

Work Order Description

Nominal Value

Check: Vehicle Configuration

Is the following information correct for the actual vehicle?

Check: Refrigerant Circuit

Note:

Do not check the air conditioning system in immediate vicinity of walls (Distance approximately 2 m ), in order to guarantee a sufficient air circulation at the condenser.

• Connect service station to the air conditioning system
• Read high pressure gauge
• Select the following Functional System on the diagnostic tester:
  Motronic 7.6.1. Z 12 XEP, Z 14 XEP, Z 14 XEL
• Compare the following data list parameters:
  A/C Pressure (Air Conditioning)

Note:

The datalist parameter shows the absolute pressure. The manometers of A/C-Service-Devices usually show relative pressure. That may cause a difference in the reading of approximately 100 kPa ( 1 bar ).

Does the corresponding data list parameter show the correct value?

Check: Refrigerant Circuit

• Check the following data list parameters:
  A/C Pressure (Air Conditioning)

Air conditioning system pressure is in the range from 320 kPa ( 3.2 bar ) and 2800 kPa ( 28 bar )

Check: Functional Group

Perform the following test step:

After successful test/fault repair proceed to the next test step

Check: Function of the Air Conditioning System

• Check the condenser for blocked section by dirt.

Test okay?

Check: Function of the Air Conditioning System

Perform the following test step:

After successful test/fault repair proceed to the next test step

Check: Functional Group

Perform the following test step:

After successful test/fault repair proceed to the next test step

Check: Short to Voltage/Ground/Interruption of Signal Circuit

Perform the following test step:

After successful test/fault repair proceed to the next test step

Check: Vehicle Configuration

Is the following information correct for the actual vehicle?

Check: Refrigerant Circuit

Note:

Do not check the air conditioning system in immediate vicinity of walls (Distance approximately 2 m ), in order to guarantee a sufficient air circulation at the condenser.

• Connect service station to the air conditioning system
• Read high pressure gauge
• Select the following Functional System on the diagnostic tester:
  Multec S (F), Z 16 XEP, Z 16 XE1
• Compare the following data list parameters:
  A/C Pressure (Air Conditioning)

Note:

The datalist parameter shows the absolute pressure. The manometers of A/C-Service-Devices usually show relative pressure. That may cause a difference in the reading of approximately 100 kPa ( 1 bar ).

Does the corresponding data list parameter show the correct value?

Check: Refrigerant Circuit

• Check the following data list parameters:
  A/C Pressure (Air Conditioning)

Air conditioning system pressure is in the range from 320 kPa ( 3.2 bar ) and 2800 kPa ( 28 bar )

Check: Vehicle Configuration

Is the following information correct for the actual vehicle?

Check: Refrigerant Circuit

Note:

Do not check the air conditioning system in immediate vicinity of walls (Distance approximately 2 m ), in order to guarantee a sufficient air circulation at the condenser.

• Connect service station to the air conditioning system
• Read high pressure gauge
• Select the following Functional System on the diagnostic tester:
  Simtec 71.5, Z 18 XE
• Compare the following data list parameters:
  A/C Pressure (Air Conditioning)

Note:

The datalist parameter shows the absolute pressure. The manometers of A/C-Service-Devices usually show relative pressure. That may cause a difference in the reading of approximately 100 kPa ( 1 bar ).

Does the corresponding data list parameter show the correct value?

Check: Refrigerant Circuit

• Check the following data list parameters:
  A/C Pressure (Air Conditioning)

Air conditioning system pressure is in the range from 320 kPa ( 3.2 bar ) and 2800 kPa ( 28 bar )

Check: Vehicle Configuration

Is the following information correct for the actual vehicle?

Check: Refrigerant Circuit

Note:

Do not check the air conditioning system in immediate vicinity of walls (Distance approximately 2 m ), in order to guarantee a sufficient air circulation at the condenser.

• Connect service station to the air conditioning system
• Read high pressure gauge
• Select the following Functional System on the diagnostic tester:
  Motronic 7.6.1, Z 20 LEH, Z 20 LEL, Z 20 LER
• Compare the following data list parameters:
  A/C Pressure (Air Conditioning)

Note:

The datalist parameter shows the absolute pressure. The manometers of A/C-Service-Devices usually show relative pressure. That may cause a difference in the reading of approximately 100 kPa ( 1 bar ).

Does the corresponding data list parameter show the correct value?

Check: Refrigerant Circuit

• Check the following data list parameters:
  A/C Pressure (Air Conditioning)

Air conditioning system pressure is in the range from 320 kPa ( 3.2 bar ) and 2800 kPa ( 28 bar )

Check: Vehicle Configuration

Is the following information correct for the actual vehicle?

Check: Refrigerant Circuit

Note:

Do not check the air conditioning system in immediate vicinity of walls (Distance approximately 2 m ), in order to guarantee a sufficient air circulation at the condenser.

• Connect service station to the air conditioning system
• Read high pressure gauge
• Select the following Functional System on the diagnostic tester:
  Electronic Diesel Injection System EDC 16C9, Z 17 DTL, Z 17 DTH
• Compare the following data list parameters:
  A/C Pressure (Air Conditioning)

Note:

The datalist parameter shows the absolute pressure. The manometers of A/C-Service-Devices usually show relative pressure. That may cause a difference in the reading of approximately 100 kPa ( 1 bar ).

Does the corresponding data list parameter show the correct value?

Check: Refrigerant Circuit

• Check the following data list parameters:
  A/C Pressure (Air Conditioning)

Air conditioning system pressure is in the range from 320 kPa ( 3.2 bar ) and 2800 kPa ( 28 bar )

Check: Vehicle Configuration

Is the following information correct for the actual vehicle?

Check: Refrigerant Circuit

Note:

Do not check the air conditioning system in immediate vicinity of walls (Distance approximately 2 m ), in order to guarantee a sufficient air circulation at the condenser.

• Connect service station to the air conditioning system
• Read high pressure gauge
• Select the following Functional System on the diagnostic tester:
  Electronic Diesel Injection System EDC 16C9/16C39, Z 19 DT, Z 19 DTH, Z 19 DTL
• Compare the following data list parameters:
  A/C Pressure (Air Conditioning)

Note:

The datalist parameter shows the absolute pressure. The manometers of A/C-Service-Devices usually show relative pressure. That may cause a difference in the reading of approximately 100 kPa ( 1 bar ).

Does the corresponding data list parameter show the correct value?

Check: Refrigerant Circuit

• Check the following data list parameters:
  A/C Pressure (Air Conditioning)

Air conditioning system pressure is in the range from 320 kPa ( 3.2 bar ) and 2800 kPa ( 28 bar )

Check: Vehicle Configuration

Is the following information correct for the actual vehicle?

Check: Refrigerant Circuit

Note:

Do not check the air conditioning system in immediate vicinity of walls (Distance approximately 2 m ), in order to guarantee a sufficient air circulation at the condenser.

• Connect service station to the air conditioning system
• Read high pressure gauge
• Select the following Functional System on the diagnostic tester:
  Electronic Diesel Injection System Multijet 6JO, Z 13 DTH
• Compare the following data list parameters:
  A/C Pressure (Air Conditioning)

Note:

The datalist parameter shows the absolute pressure. The manometers of A/C-Service-Devices usually show relative pressure. That may cause a difference in the reading of approximately 100 kPa ( 1 bar ).

Does the corresponding data list parameter show the correct value?

Check: Refrigerant Circuit

• Check the following data list parameters:
  A/C Pressure (Air Conditioning)

Air conditioning system pressure is in the range from 320 kPa ( 3.2 bar ) and 2800 kPa ( 28 bar )

Check: Vehicle Configuration

Is the following information correct for the actual vehicle?

Check: Refrigerant Circuit

Note:

Do not check the air conditioning system in immediate vicinity of walls (Distance approximately 2 m ), in order to guarantee a sufficient air circulation at the condenser.

• Connect service station to the air conditioning system
• Read high pressure gauge
• Select the following Functional System on the diagnostic tester:
  Simtec 75, Z 18 XER
• Compare the following data list parameters:
  A/C Pressure (Air Conditioning)

Note:

The datalist parameter shows the absolute pressure. The manometers of A/C-Service-Devices usually show relative pressure. That may cause a difference in the reading of approximately 100 kPa ( 1 bar ).

Does the corresponding data list parameter show the correct value?

Check: Refrigerant Circuit

• Check the following data list parameters:
  A/C Pressure (Air Conditioning)

Air conditioning system pressure is in the range from 320 kPa ( 3.2 bar ) and 2800 kPa ( 28 bar )

Check: Vehicle Configuration

Is the following information correct for the actual vehicle?

Check: Refrigerant Circuit

Note:

Do not check the air conditioning system in immediate vicinity of walls (Distance approximately 2 m ), in order to guarantee a sufficient air circulation at the condenser.

• Connect service station to the air conditioning system
• Read high pressure gauge
  Select the following Functional System on the diagnostic tester:
  Motronic 7.6.2, A 16 LET, Z 16 LET
• Compare the following data list parameters:
  A/C Pressure (Air Conditioning)

Note:

The datalist parameter shows the absolute pressure. The manometers of A/C-Service-Devices usually show relative pressure. That may cause a difference in the reading of approximately 100 kPa ( 1 bar ).

Does the corresponding data list parameter show the correct value?

Check: Refrigerant Circuit

• Check the following data list parameters:
  A/C Pressure (Air Conditioning)

Air conditioning system pressure is in the range from 320 kPa ( 3.2 bar ) and 2800 kPa ( 28 bar )

Check: Vehicle Configuration

Is the following information correct for the actual vehicle?

Check: Refrigerant Circuit

Note:

Do not check the air conditioning system in immediate vicinity of walls (Distance approximately 2 m ), in order to guarantee a sufficient air circulation at the condenser.

• Connect service station to the air conditioning system
• Read high pressure gauge
• Select the following Functional System on the diagnostic tester:
  Electronic Diesel Injection System DECE1C, A 17 DTJ, A 17 DTR, Z 17 DTJ, Z 17 DTR
• Compare the following data list parameters:
  A/C Pressure (Air Conditioning)

Note:

The datalist parameter shows the absolute pressure. The manometers of A/C-Service-Devices usually show relative pressure. That may cause a difference in the reading of approximately 100 kPa ( 1 bar ).

Does the corresponding data list parameter show the correct value?

Check: Refrigerant Circuit

• Check the following data list parameters:
  A/C Pressure (Air Conditioning)

Air conditioning system pressure is in the range from 320 kPa ( 3.2 bar ) and 2800 kPa ( 28 bar )

Check: Vehicle Configuration

Is the following information correct for the actual vehicle?

Check: Refrigerant Circuit

Note:

Do not check the air conditioning system in immediate vicinity of walls (Distance approximately 2 m ), in order to guarantee a sufficient air circulation at the condenser.

• Connect service station to the air conditioning system
• Read high pressure gauge
• Select the following Functional System on the diagnostic tester:
  Simtec 75, Z 16 XER
• Compare the following data list parameters:
  A/C Pressure (Air Conditioning)

Note:

The datalist parameter shows the absolute pressure. The manometers of A/C-Service-Devices usually show relative pressure. That may cause a difference in the reading of approximately 100 kPa ( 1 bar ).

Does the corresponding data list parameter show the correct value?

Check: Refrigerant Circuit

• Check the following data list parameters:
  A/C Pressure (Air Conditioning)

Air conditioning system pressure is in the range from 320 kPa ( 3.2 bar ) and 2800 kPa ( 28 bar )

Check: Vehicle Configuration

Is the following information correct for the actual vehicle?

Check: Refrigerant Circuit

Note:

Do not check the air conditioning system in immediate vicinity of walls (Distance approximately 2 m ), in order to guarantee a sufficient air circulation at the condenser.

• Connect service station to the air conditioning system
• Read high pressure gauge
• Select the following Functional System on the diagnostic tester:
  Simtec 81, Z 22 YH
• Compare the following data list parameters:
  A/C Pressure (Air Conditioning)

Note:

The datalist parameter shows the absolute pressure. The manometers of A/C-Service-Devices usually show relative pressure. That may cause a difference in the reading of approximately 100 kPa ( 1 bar ).

Does the corresponding data list parameter show the correct value?

Check: Refrigerant Circuit

• Check the following data list parameters:
  A/C Pressure (Air Conditioning)

Air conditioning system pressure is in the range from 320 kPa ( 3.2 bar ) and 2800 kPa ( 28 bar )

Invalid / not supported vehicle configuration

The selected Checking Procedure is not valid for this vehicle configuration.