Special Service Tools
KM-161-B
|
Pusher tool
|
Press tie rod end out of steering knuckle
|
|
|
KM-301
|
Measuring bridge
|
|
Measure the piston projection
|
|
|
KM-313
|
Plane hammer
|
|
Remove axle body in connection with KM-902
|
|
|
KM-328-B
|
Puller
|
|
Pulling out various bearings and plugs
|
|
|
KM-412-A
|
Engine Overhaul Stand
|
|
To hold the removed engine
|
|
|
KM-412-36
|
Engine adapter
|
|
To hold engine in conjunction with KM-412-A
|
|
|
KM-468-B
|
Holding Wrench
|
Counterhold wheel hub when fitting axle nut
|
|
|
KM-470-B
|
Angular Torque Wrench
|
Tightening cylinder head bolts according to angle°
|
|
|
KM-471
|
Adapter
|
Check pressurised cooling system in conjunction with cooling
system tester
|
|
|
KM-498-B
|
Oil Pressure Manometer
|
Engine oil pressure with KM-6342
|
|
|
MKM-558-10
|
Closure cap
|
|
Sealing brake fluid reservoir
|
|
|
KM-596-A
|
Temperature measuring device
|
Temperature gauge
|
|
|
MKM-604-D
|
Torx Bit and Socket Set
|
Removing and installing torx bolts
|
|
|
MKM-610
|
Torque Wrench, 1/2"
|
|
Range 30 - 130 Nm
|
|
|
MKM-611
|
Torque Wrench, 3/8"
|
|
Range 10 - 60 Nm
|
|
|
KM-662-C
|
Holding Wrench
|
Toothed belt drive gear, slackening/tightening bolt
|
|
|
MKM-669
|
Torque Wrench, 1/2"
|
|
Range 50 – 300 Nm
|
|
|
KM-796-A
|
Assembly clamp
|
|
To open quick-release fittings for fuel system
|
|
|
KM-807
|
Sealing plug
|
|
Sealing the fuel lines
|
|
|
MKM-883-2
|
Adapter plate
|
|
Holding the engine together with MKM-883-1 and MKM-883-3
|
|
|
KM-902
|
Remover
|
|
Removing axle bodies in conjunction with KM-313
|
|
|
KM-904
|
Base Frame
|
To remove/install engine and transmission with KM-6001-A
|
|
|
KM-913-A
|
Installation Wrench
|
|
Tension the ribbed V-belt tension roller
|
|
|
KM-915
|
Expander
|
To remove guide joint from steering knuckle
|
|
|
KM-956-1
|
Grip
|
Holding camshaft timing gears to slacken/tighten bolt in
conjunction with KM-6347
|
|
|
KM-2358
|
Wire ropes
|
|
Hitching engine
|
|
|
KM-6001-A
|
Engine Mount
|
To centre engine in conjunction with MKM-6173
|
|
|
KM-6015
|
Sealing plug
|
Sealing the fuel lines
|
|
|
KM-6042
|
Remover
|
Remove shift cables from shift guide assembly
|
|
|
KM-6129
|
Remover/Installer
|
Removal/installation of oxygen sensors in manifold using
MKM-611
|
|
|
KM-6182-1
|
Pliers, straight
|
|
Removing and installing space-saving clamps
|
|
|
KM-6182-2
|
Pliers, curved
|
|
Removing and installing space-saving clamps
|
|
|
KM-6182-3
|
Pliers, flexible shaft
|
|
Removing and installing space-saving clamps
|
|
|
KM-6327
|
Adapter
|
|
Seal coolant compensation tank to check cooling system for leaks
- with KM-471
|
|
|
KM-6347
|
Holder
|
Holding camshaft timing gears to slacken/tighten bolts in
conjunction with KM-956-1
|
|
|
KM-6349
|
Fixing rod
|
To fix tensioning pulley of ribbed V-belt
|
|
|
KM-6390
|
Centring Tool
|
Removing and installing front axle and aligning subframe to
vehicle underbody in conjunction with KM-904 and hydraulic jack
|
|
|
MKM-J-6459-B
|
Torque Wrench, 3/8"
|
|
Range 0 - 11 Nm
|
|
|
MKM-6600-1
|
Torque wrench 4-40 Nm
|
Small torque wrench with narrow range for use in restricted
spaces, together with MKM-6600-100, MKM-6600-200 and
MKM-6600-300
|
|
|
MKM-6600-2
|
Torque wrench 20-120 Nm
|
Large torque wrench with wide range for use in restriced spaces,
together with MKM-6600-100, MKM-6600-200 and MKM-6600-300
|
|
|
MKM-6600-100
|
Torque wrench socket set
|
Sizes: E8, E10, E11, E12, E14, E16, E18, E20, E22, E24 for use
in constricted spaces, together with MIM-6600-1 and MKM-6600-2
|
|
|
MKM-6600-200
|
Box spanner socket set
|
Sizes:10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 21, 22, 24, 27 for
use in constricted spaces, together with MIM-6600-1 and
MKM-6600-2
|
|
|
MKM-6600-300
|
Open-ended spanner socket set
|
Sizes:10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 21, 22, 24, 27 for
use in constricted spaces, together with MIM-6600-1 and
MKM-6600-2
|
|
|
KM-J-37228
|
Separation Tool
|
To disconnect oil pan
|
|
|
EN-46783
|
Adapter
|
|
For checking compression together with EN-46791
|
|
|
EN-46786
|
Remover
|
|
Removing injectors in conjunction with KM-328-B
|
|
|
EN-46787
|
Holder
|
|
Holding camshaft sprocket when slackening/tightening fastening
bolt - together with KM-956-1
|
|
|
EN-46788
|
Locking Tool
|
|
Attach crankshaft sprocket
|
|
|
EN-46789
|
Locking Tool
|
|
Attach camshafts
|
|
|
EN-46790
|
Remover
|
|
Detach diesel fuel high pressure pump drive gear
|
|
|
EN-46792
|
Flywheel Locking Device
|
|
To lock flywheel or drive disc
|
|
|
EN-46793
|
Installer
|
|
Installation of oil pump seal ring, crankshaft, front
|
|
|
EN-46794
|
Socket wrench
|
|
Remove/install oil pan screws at transmission side
|
|
|
EN-46796
|
Socket wrench
|
|
Remove/install oil pan screws
|
|
|
EN-46797
|
Valve Lifter Depressor
|
|
Depression of valve tappet together with EN-46799
|
|
|
EN-46799
|
Locking Tool
|
|
Securing the valve tappet in lower position together with
EN-46797
|
|
|
EN-47630
|
Crankshaft retainer
|
|
Holding toothed belt drive gear of crankshaft together with
KM-956-1
|
|
|
EN-47631
|
Socket wrench, short
|
|
Remove/install oil pan screws via subframe
|
|
|
EN-47632
|
Cleaner
|
|
Cleaning the injector shaft
|
|
|
EN-47656-1
|
Pressure test plug - connection piece
|
|
Testing seal of charge air system in conjunction with tyre
filling device
|
|
|
EN-47656-2
|
Pressure testing plug
|
|
Testing seal of charge air system in conjunction with tyre
filling device
|
|
|
EN-48389
|
Removing/installing wrench
|
|
Glow plug removal/installation, SW 10 mm
|
|
|
|