Test
|
Work Order Description
|
Nominal Value
|
T001
|
Tester Display Battery Voltage
|
- Ignition ON
- Engine OFF
- All consumers turned off
|
11 ... 13.5 V
|
|
greater than 8 V
|
- Engine running at idle speed, operating temperature
- All consumers turned off
- Accelerator pedal not actuated
|
12 ... 15 V
|
Concerned Terminals: ECM: 64 (XC4)
|
|
|
T002
|
Tester Display Fuel Pump Relay
|
- Ignition ON
- Engine OFF
- All consumers turned off
|
Inactive
|
- Engine running at idle speed, operating temperature
- Accelerator pedal not actuated
|
Active
|
Concerned Terminals: ECM: 19 (XC4)
|
|
|
T003
|
Tester Display APP at Idle Position (Accelerator Pedal Position)
|
- Engine running at idle speed, operating temperature
- All consumers turned off
- Accelerator pedal not actuated
|
Active
|
- Accelerator pedal slightly actuated
|
Inactive
|
Concerned Terminals: ECM: 8, 24, 39, 40, 55, 56 (XC4)
|
|
|
T004
|
Tester Display APP Sensor 1 (Accelerator Pedal Position)
|
- Ignition ON
- Engine OFF
- All consumers turned off
- Accelerator pedal not actuated
|
less than 1 V
|
- Accelerator pedal slightly actuated
|
1 ... 4 V
|
- Accelerator pedal actuated to full load stop
|
greater than 4 V
|
Concerned Terminals: ECM: 8, 24, 39, 40, 55, 56 (XC4)
|
|
|
T005
|
Tester Display APP Sensor 2 (Accelerator Pedal Position)
|
- Ignition ON
- Engine OFF
- All consumers turned off
- Accelerator pedal not actuated
|
less than 0.5 V
|
- Accelerator pedal slightly actuated
|
0.7 ... 1.5 V
|
- Accelerator pedal actuated to full load stop
|
greater than 2.0 V
|
Concerned Terminals: ECM: 8, 24, 39, 40, 55, 56 (XC4)
|
|
|
T006
|
Tester Display Calculated Pedal Position
|
- Ignition ON
- Engine OFF
- All consumers turned off
- Accelerator pedal not actuated
|
0 %
|
- Accelerator pedal actuated to full load stop
|
greater than 90 %
|
Concerned Terminals: ECM: 8, 24, 39, 40, 55, 56 (XC4)
|
|
|
T007
|
Tester Display TP Sensor 1 (Throttle Position)
|
- Engine running at idle speed, operating temperature
- All consumers turned off
- Accelerator pedal not actuated
|
less than 0.65 V
|
- Accelerator pedal slightly actuated
|
0.7 ... 2.0 V
|
- Accelerator pedal briefly actuated to full load stop
|
greater than 2.0 V
|
Concerned Terminals: ECM: 3, 10, 13, 20, 26, 30, 42, 45, 58, 62 (XC3)
|
|
|
T008
|
Tester Display TP Sensor 2 (Throttle Position)
|
- Engine running at idle speed, operating temperature
- All consumers turned off
- Accelerator pedal not actuated
|
greater than 4.2 V
|
- Accelerator pedal slightly actuated
|
less than 4.0 V
|
Concerned Terminals: ECM: 3, 10, 13, 20, 26, 30, 42, 45, 58, 62 (XC3)
|
|
|
T009
|
Tester Display Calculated Throttle Position
|
- Engine running at idle speed, operating temperature
- All consumers turned off
- Accelerator pedal not actuated
|
less than 5 %
|
- Accelerator pedal briefly actuated to full load stop
|
greater than 10 %
Value changing briefly
|
Concerned Terminals: ECM: 3, 10, 13, 20, 26, 30, 42, 45, 58, 62 (XC3)
|
|
|
T010
|
Tester Display Throttle Position PWM Servo Signal
|
- Engine running at idle speed, operating temperature
- All consumers turned off
- Accelerator pedal not actuated
|
greater than 90 %
|
- Accelerator pedal briefly actuated to full load stop
|
less than 90 %
Value changing briefly
|
Concerned Terminals: ECM: 3, 10, 13, 20, 26, 30, 42, 45, 58, 62 (XC3)
|
|
|
T011
|
Tester Display Throttle Position
|
- Engine running at idle speed, operating temperature
- All consumers turned off
- Accelerator pedal not actuated
|
Idle
|
- Accelerator pedal slightly actuated
|
Partial Load
|
- Accelerator pedal briefly actuated to full load stop
|
Full Load
|
Concerned Terminals: ECM: 3, 10, 13, 20, 26, 30, 42, 45, 58, 62 (XC3)
|
|
|
T012
|
Tester Display TP Sensor 1 Learned Lower Position (Throttle Position)
|
- Engine running at idle speed, operating temperature
- All consumers turned off
- Accelerator pedal not actuated
|
less than 1.0 V
|
Concerned Terminals: ECM: 3, 10, 13, 20, 26, 30, 42, 45, 58, 62 (XC3)
|
|
|
T013
|
Tester Display TP Sensor 2 Learned Lower Position (Throttle Position)
|
- Engine running at idle speed, operating temperature
- All consumers turned off
- Accelerator pedal not actuated
|
greater than 2.0 V
|
Concerned Terminals: ECM: 3, 10, 13, 20, 26, 30, 42, 45, 58, 62 (XC3)
|
|
|
T014
|
Tester Display Desired Engine Idle Speed
|
- Engine running at idle speed, operating temperature
- All consumers turned off
- Accelerator pedal not actuated
|
650 ... 950 rpm
|
Concerned Terminals: ECM: 3, 10, 13, 20, 26, 30, 42, 45, 58, 62 (XC3)
|
|
|
T015
|
Tester Display Engine Speed
|
- Ignition ON
- Engine starting
|
greater than 60 rpm
|
Concerned Terminals: ECM: 5, 33, 37 (XC3)
|
|
|
T016
|
Tester Display Mass Air Flow Sensor
|
- Engine running at idle speed, operating temperature
- All consumers turned off
- Accelerator pedal not actuated
|
7 ... 19 kg/h
0.2 ... 1.2 V
|
Concerned Terminals: ECM: 43 (XC3)
|
|
|
T017
|
Tester Display Intake Air Temperature
|
- Engine running at idle speed, operating temperature
- All consumers turned off
- Accelerator pedal not actuated
|
10 ... 80 °C
50 ... 176 °F
2.5 ... 1.0 V
|
Concerned Terminals: ECM: 27, 41 (XC3)
|
|
|
T018
|
Tester Display Coolant Temperature
|
- Engine running at idle speed, operating temperature
- All consumers turned off
- Accelerator pedal not actuated
|
80 ... 110 °C
176 ... 230 °F
2.0 ... 1.1 V
|
Concerned Terminals: ECM: 25 (XC3)
|
|
|
T019
|
Tester Display Oil Level
|
- Ignition ON
- Engine OFF
- All consumers turned off
|
Normal
|
Concerned Terminals: ECM: 59 (XC4)
|
|
|
T020
|
Tester Display Oil Pressure
|
- Ignition ON
- Engine OFF
- All consumers turned off
|
Low Pressure
|
- Engine running at idle speed, operating temperature
- Accelerator pedal not actuated
|
Normal
|
Concerned Terminals: ECM: 60 (XC3)
|
|
|
T021
|
Tester Display Engine Oil Level Status
|
- Ignition ON
- Engine OFF
- All consumers turned off
|
Okay
|
Concerned Terminals: ECM: 59 (XC4)
|
|
|
T022
|
Tester Display A/C Information Switch (Air Conditioning)
|
- Engine idling
- All consumers turned off
- Air conditioning system switch OFF
|
|
Default
|
Not Programmed
The data list parameter is invalid for this configuration
|
(Air Conditioning (not ECC))
|
Inactive
|
(Electronic Climate Control ECC), (Air Conditioning Compressor without Clutch)
|
Not Programmed
The data list parameter is invalid for this configuration
|
(Electronic Climate Control ECC), (Air Conditioning Compressor with Clutch)
|
Inactive
|
(Automatic Climate Control SAC)
|
Inactive
|
- Air conditioning system switch ON
|
|
Default
|
Not Programmed
The data list parameter is invalid for this configuration
|
(Electronic Climate Control ECC), (Air Conditioning Compressor without Clutch)
|
Not Programmed
The data list parameter is invalid for this configuration
|
(Air Conditioning (not ECC))
|
Active
|
(Electronic Climate Control ECC), (Air Conditioning Compressor with Clutch)
|
Active
|
(Automatic Climate Control SAC)
|
Active
|
Concerned Terminals: ECM: 51 (XC4)
|
|
|
T023
|
Tester Display A/C Pressure (Air Conditioning)
|
- Engine running at idle speed, operating temperature
- All consumers turned off
- Accelerator pedal not actuated
|
|
Default
|
The data list parameter is invalid for this configuration
|
(Air Conditioning (not ECC))
|
320 ... 3100 kPa
|
(Electronic Climate Control ECC), (Air Conditioning Compressor without Clutch)
|
320 ... 3100 kPa
|
(Electronic Climate Control ECC), (Air Conditioning Compressor with Clutch)
|
320 ... 3100 kPa
|
(Automatic Climate Control SAC)
|
320 ... 3100 kPa
|
- Air conditioning system switch ON
|
|
Default
|
The data list parameter is invalid for this configuration
|
(Electronic Climate Control ECC), (Air Conditioning Compressor with Clutch)
|
Is there a pressure difference of at least 500 kPa ?
|
(Air Conditioning (not ECC))
|
Is there a pressure difference of at least 500 kPa ?
|
(Electronic Climate Control ECC), (Air Conditioning Compressor without Clutch)
|
Is there a pressure difference of at least 500 kPa ?
|
(Automatic Climate Control SAC)
|
Is there a pressure difference of at least 500 kPa ?
|
Concerned Terminals: ECM: 7, 23, 34 (XC4)
|
|
|
T024
|
Tester Display A/C Cutoff Mode (Air Conditioning)
|
- Engine idling
- Coolant temperature between 60 °C (140 °F) and 115 °C (239 °F)
- Air conditioning system pressure is in the range from 320 kPa ( 3.2 bar ) and 3100 kPa ( 31 bar )
- Accelerator pedal not actuated
|
|
Default
|
Not Programmed
The data list parameter is invalid for this configuration
|
(Air Conditioning (not ECC))
|
System OK
|
(Electronic Climate Control ECC), (Air Conditioning Compressor without Clutch)
|
System OK
|
(Electronic Climate Control ECC), (Air Conditioning Compressor with Clutch)
|
System OK
|
(Automatic Climate Control SAC)
|
System OK
|
Concerned Terminals: ECM: 7, 23, 34 (XC4)
|
|
|
T025
|
Tester Display A/C Relay (Air Conditioning)
|
- Engine running at idle speed, operating temperature
- All consumers turned off
- Accelerator pedal not actuated
|
|
Default
|
Not Programmed
The data list parameter is invalid for this configuration
|
(Air Conditioning (not ECC))
|
Inactive
|
(Electronic Climate Control ECC), (Air Conditioning Compressor without Clutch)
|
Not Programmed
The data list parameter is invalid for this configuration
|
(Electronic Climate Control ECC), (Air Conditioning Compressor with Clutch)
|
Inactive
|
(Automatic Climate Control SAC)
|
Inactive
|
- Air conditioning system switch ON
|
|
Default
|
Not Programmed
The data list parameter is invalid for this configuration
|
(Electronic Climate Control ECC), (Air Conditioning Compressor without Clutch)
|
Not Programmed
The data list parameter is invalid for this configuration
|
(Air Conditioning (not ECC))
|
Active
|
(Electronic Climate Control ECC), (Air Conditioning Compressor with Clutch)
|
Active
|
(Automatic Climate Control SAC)
|
Active
|
Concerned Terminals: ECM: 51 (XC4)
|
|
|
T026
|
Tester Display Brake Switch 1
|
- Ignition ON
- Engine OFF
- All consumers turned off
- Brake pedal not actuated
|
Inactive
|
|
Active
|
Concerned Terminals: ECM: 28, 42 (XC4)
|
|
|
T027
|
Tester Display Brake Switch 2
|
- Ignition ON
- Engine OFF
- All consumers turned off
- Brake pedal not actuated
|
Inactive
|
|
Active
|
Concerned Terminals: ECM: 28, 42 (XC4)
|
|
|
T028
|
Tester Display Park/Neutral Switch
|
- Ignition ON
- Engine OFF
- All consumers turned off
- Brake pedal actuated
- Selector lever in position P - N
|
|
(Front Wheel Drive, Automatic Transmission, AF 17-4)
|
P - N
|
(Front Wheel Drive, Manual Transmission)
|
Not Used
|
- Selector lever in position R - D
|
|
(Front Wheel Drive, Automatic Transmission, AF 17-4)
|
R - D
|
(Front Wheel Drive, Manual Transmission)
|
Not Used
|
Concerned Terminals: ECM: -
|
|
|
T029
|
Tester Display Clutch Switch
|
- Ignition ON
- Engine OFF
- All consumers turned off
- Do not actuate clutch pedal
|
|
Default
|
Not Programmed
The data list parameter is invalid for this configuration
|
(Electronic Cruise Control)
|
Inactive
|
|
|
Default
|
Not Programmed
The data list parameter is invalid for this configuration
|
(Electronic Cruise Control)
|
Active
|
Concerned Terminals: ECM: 10 (XC4)
|
|
|
T030
|
Tester Display Vehicle Speed
|
- Vehicle travelling (constant speed, approximately 30 km/h (19 mph))
|
30 km/h
19 mph
Diagnostic tester display converges to speedometer display
|
Concerned Terminals: ECM: -
|
|
|
T031
|
Tester Display Cruise Control Tip Switch
|
- Ignition ON
- Engine OFF
- All consumers turned off
- Key " I " not pressed
|
|
Default
|
Not Programmed
|
(Electronic Cruise Control)
|
Inactive
|
- Key " I " pressed briefly
|
|
Default
|
Not Programmed
|
(Electronic Cruise Control)
|
I (set)
|
|
|
Default
|
Not Programmed
|
(Electronic Cruise Control)
|
Inactive
|
- Key " R " pressed briefly
|
|
Default
|
Not Programmed
|
(Electronic Cruise Control)
|
R (Resume)
|
|
|
Default
|
Not Programmed
|
(Electronic Cruise Control)
|
Inactive
|
- Key " O " pressed briefly
|
|
Default
|
Not Programmed
|
(Electronic Cruise Control)
|
O (off)
|
Concerned Terminals: CIM: 1, 3 (XC48)
|
|
|
T032
|
Tester Display Cruise Control
|
- Engine running at idle speed, operating temperature
- Brake pedal actuated
- Vehicle stationary
- Key " I " not pressed
|
|
Default
|
Not Programmed
|
(Electronic Cruise Control)
|
Inactive
|
- Vehicle travelling (constant speed, approximately 40 km/h (25 mph))
- Brake pedal not actuated
- Clutch pedal not actuated/selector lever in position D
- Cruise control active
|
|
Default
|
Not Programmed
|
(Electronic Cruise Control)
|
Active
|
Concerned Terminals: CIM: 1, 3 (XC48)
|
|
|
T033
|
Tester Display Vehicle Speed in Cruise Control Range
|
- Vehicle accelerated from stop (from 0 km/h (0 mph) up to approximately 25 km/h (16 mph))
|
|
Default
|
Not Programmed
The data list parameter is invalid for this configuration
|
(Electronic Cruise Control)
|
Inactive
|
- Vehicle speed is greater than 30 km/h (19 mph)
|
|
Default
|
Not Programmed
The data list parameter is invalid for this configuration
|
(Electronic Cruise Control)
|
Active
|
Concerned Terminals: CIM: 1, 3 (XC48)
|
|
|
T034
|
Tester Display Fuel Tank Ventilation Valve
|
- Engine running at idle speed, operating temperature
- All consumers turned off
- Accelerator pedal not actuated
|
Inactive
0 %
|
- Accelerator pedal briefly actuated to full load stop
|
Active
greater than 0 %
|
Concerned Terminals: ECM: 34 (XC3)
|
|
|
T035
|
Tester Display Deceleration Fuel Cutoff
|
- Engine running at idle speed, operating temperature
- All consumers turned off
- Accelerator pedal not actuated
|
Inactive
|
- Vehicle travelling (coasting, approximately 30 km/h (19 mph))
|
Active
Value changing briefly
|
Concerned Terminals: ECM: -
|
|
|
T036
|
Tester Display Knock Control
|
- Engine running at idle speed, operating temperature
- All consumers turned off
- Accelerator pedal not actuated
|
Inactive
|
- Accelerator pedal briefly actuated to full load stop
|
Active
Value changing briefly
|
Concerned Terminals: ECM: 17, 33, 49 (XC3)
|
|
|
T037
|
Tester Display Knock Retard Cylinder 1
|
- Engine running at idle speed, operating temperature
- All consumers turned off
- Accelerator pedal not actuated
|
0 °CA
|
- Accelerator pedal briefly actuated to full load stop
|
greater than 0 °CA
|
Concerned Terminals: ECM: 17, 33, 49 (XC3)
|
|
|
T038
|
Tester Display Knock Retard Cylinder 2
|
- Engine running at idle speed, operating temperature
- All consumers turned off
- Accelerator pedal not actuated
|
0 °CA
|
- Accelerator pedal briefly actuated to full load stop
|
greater than 0 °CA
|
Concerned Terminals: ECM: 17, 33, 49 (XC3)
|
|
|
T039
|
Tester Display Knock Retard Cylinder 3
|
- Engine running at idle speed, operating temperature
- All consumers turned off
- Accelerator pedal not actuated
|
0 °CA
|
- Accelerator pedal briefly actuated to full load stop
|
greater than 0 °CA
|
Concerned Terminals: ECM: 17, 33, 49 (XC3)
|
|
|
T040
|
Tester Display Knock Retard Cylinder 4
|
- Engine running at idle speed, operating temperature
- All consumers turned off
- Accelerator pedal not actuated
|
0 °CA
|
- Accelerator pedal briefly actuated to full load stop
|
greater than 0 °CA
|
Concerned Terminals: ECM: 17, 33, 49 (XC3)
|
|
|
T041
|
Tester Display B1S1 O2 Sensor Heater (Bank 1 Sensor 1)
|
- Ignition ON
- Engine OFF
- All consumers turned off
|
Inactive
|
- Engine running at idle speed, operating temperature
- Accelerator pedal not actuated
|
Active
Diagnostic tester displays alternately:
ACTIVE and INACTIVE
|
Concerned Terminals: ECM: 19, 35 (XC3)
|
|
|
T042
|
Tester Display B1S2 O2 Sensor Heater (Bank 1 Sensor 2)
|
- Ignition ON
- Engine OFF
- All consumers turned off
|
Inactive
|
- Engine running at idle speed, operating temperature
- Accelerator pedal not actuated
|
Active
Diagnostic tester displays alternately:
ACTIVE and INACTIVE
|
Concerned Terminals: ECM: 18 , 51 (XC3)
|
|
|
T043
|
Tester Display B1S1 O2 Sensor (Bank 1 Sensor 1)
|
- Engine running at idle speed, operating temperature
- All consumers turned off
- Accelerator pedal not actuated
|
50 ... 950 mV
Sensor signal alternates between high and low voltage range
|
Concerned Terminals: ECM: 8, 57 (XC3)
|
|
|
T044
|
Tester Display B1S2 O2 Sensor (Bank 1 Sensor 2)
|
- Engine running at idle speed, operating temperature
- All consumers turned off
- Accelerator pedal not actuated
|
50 ... 950 mV
|
Concerned Terminals: ECM: 24, 40 (XC3)
|
|
|
T045
|
Tester Display B1 O2 Sensor Loop (Bank 1)
|
- Engine running at idle speed, operating temperature
- All consumers turned off
- Accelerator pedal not actuated
|
Closed
|
Concerned Terminals: ECM: 8, 57 (XC3)
|
|
|
T046
|
Tester Display B1S1 Air/Fuel Ratio (Bank 1 Sensor 1)
|
- Engine running at idle speed, operating temperature
- All consumers turned off
- Accelerator pedal not actuated
|
Diagnostic tester displays alternately:
LEAN and RICH
|
Concerned Terminals: ECM: 8, 57 (XC3)
|
|
|
T047
|
Tester Display B1S2 Air/Fuel Ratio (Bank 1 Sensor 2)
|
- Engine running at idle speed, operating temperature
- All consumers turned off
- Accelerator pedal not actuated
|
Diagnostic tester displays alternately:
LEAN and RICH
|
Concerned Terminals: ECM: 24, 40 (XC3)
|
|
|
T048
|
Tester Display B1 Short Term Fuel Trim (Bank 1)
|
- Engine running at idle speed, operating temperature
- All consumers turned off
- Accelerator pedal not actuated
|
-5 ... 5 %
|
Concerned Terminals: ECM: 8, 57 (XC3)
|
|
|
T049
|
Tester Display Catalyst Protection Enrichment (Bank 1)
|
- Engine running at idle speed, operating temperature
- All consumers turned off
- Accelerator pedal not actuated
|
Inactive
|
- Vehicle rapidly accelerated (up to approximately 30 km/h (19 mph))
Note:
Even if the instructions given in the checking procedure are followed closely, the diagnostic tester may not indicate a signal change.
|
Active
Value changing briefly
|
Concerned Terminals: ECM: 8, 57 (XC3)
|
|
|
T050
|
Tester Display Full Load Enrichment
|
- Engine running at idle speed, operating temperature
- All consumers turned off
- Accelerator pedal not actuated
|
Inactive
|
- Accelerator pedal briefly actuated to full load stop
|
Active
Value changing briefly
|
Concerned Terminals: ECM: -
|
|
|
T051
|
Tester Display Fan Control 1
|
- Engine running
- Air conditioning system OFF
- Coolant temperature is less than 97 °C (207 °F)
|
Inactive
|
- Coolant temperature between 97 °C (207 °F) and 99 °C (210 °F)
|
Active
|
Concerned Terminals: ECM: 13 (XC4)
|
|
|
T052
|
Tester Display Fan Control 2
|
- Engine running
- Coolant temperature is less than 99 °C (210 °F)
|
Inactive
|
- Coolant temperature between 99 °C (210 °F) and 101 °C (214 °F)
|
Active
|
Concerned Terminals: ECM: 29 (XC4)
|
|
|
T053
|
Tester Display Fan Control 3
|
- Engine running
- Coolant temperature is less than 101 °C (214 °F)
|
Inactive
|
- Coolant temperature between 101 °C (214 °F) and 103 °C (217 °F)
|
Active
|
Concerned Terminals: ECM: 46 (XC4)
|
|
|
T054
|
Tester Display Intake Manifold Valve 1
|
- Engine running at idle speed, operating temperature
- All consumers turned off
- Accelerator pedal not actuated
|
Inactive
|
- Accelerator pedal briefly actuated to full load stop
|
Active
Value changing briefly
|
Concerned Terminals: ECM: 2 (XC3)
|
|
|