|
Special Service Tools
|
KM-113-2
|
Bracket
|
|
Mount for transmission bracket with KM-910
|
|
|
|
KM-161-B
|
Bearing Puller
|
|
Extracting various transmission components
|
|
|
|
KM-204
|
Knock-in sleeve
|
|
To push roller bearing into converter housing
|
|
|
|
KM-313
|
Sliding Hammer
|
|
Roller bearing from converter housing with KM-J-26941 and
KM-483
|
|
|
|
KM-328-B
|
Remover Hook
|
|
Pulling oil pump seal ring from transmission together with
KM-469-A and KM-6328
|
|
|
|
KM-372
|
Remover/Installer
|
|
To push tapered roller bearing outer race into transmission
housing with KM-372-2 in conjunction with KM-554 and KM-710
|
|
|
|
KM-396
|
Ring pliers
|
|
To remove and install various retaining rings
|
|
|
|
KM-446
|
Installer Drift
|
|
To install axle shaft seal rings (F 13/F 17+)
|
|
|
|
KM-469-A
|
Remover Hook
|
|
Pulling oil pump seal ring and sealing sleeves from transmission
together with KM-328-B and KM-6328
|
|
|
|
KM-483
|
Adapter
|
|
Roller bearing from converter housing with KM-J-26941 and
KM-313
|
|
|
|
KM-498-B
|
Pressure Gauge
|
|
Testing the fluid pressure
|
|
|
|
KM-514
|
Installer Sleeve
|
|
To remove and install various transmission parts
|
|
|
|
KM-523
|
Remover / Installer
|
|
To press tapered roller bearing outer race for differential and
friction washer in converter housing with KM-514 and KM-711-3.
|
|
|
|
MKM-536-A
|
Friction Coefficient Meter
|
|
To measure differential slip torque with KM-6037
|
|
|
|
KM-554
|
Installer
|
|
To push tapered roller bearing in transmission housing in
conjunction with KM-372-2 and KM-710
|
|
|
|
KM-557-A
|
Puller Set
|
|
To pull axle shaft seal ring from transmission
|
|
|
|
KM-567
|
Remover / Installer
|
|
Tapered roller bearing inner race from differential with
KM-514
|
|
|
|
MKM-571-B
|
Dial Gauge
|
|
Measuring various clutches and brakes
|
|
|
|
KM-574
|
Remover / Installer
|
|
Removing and installing the converter with thread
|
|
|
|
KM-580
|
Adapter
|
|
To check fluid pressure in conjunction with KM-498-B
|
|
|
|
KM-586
|
Remover Hook
|
|
To remove fluid pump seal ring with KM-J-7004
|
|
|
|
KM-620-B
|
Remover / Installer
|
|
To clamp various clutches in conjunction with KM-J-23078-A
|
|
|
|
KM-657
|
Installer
|
|
Installing sealing sleeves
|
|
|
|
KM-674-A
|
Installer
|
|
To install fluid pump seal rings
|
|
|
|
KM-697
|
Installer
|
|
To install various bearing rings in transmission
|
|
|
|
KM-710
|
Installer
|
|
Installing tapered roller bearing outer races in the
transmission housing with KM-372-2, KM-554
|
|
|
|
KM-711
|
Installer
|
|
Tapered roller bearing outer races for differential with
KM-523/4 and KM-372-2
|
|
|
|
MKM-883-1-A
|
Engine Bridge
|
|
Holding/lowering/lifting the engine
|
|
|
|
MKM-883-2
|
Retainer plate
|
|
To hold engine in conjunction with MKM-883-1-A and MKM-883-3
when removing transmission
|
|
|
|
MKM-883-3
|
Accessories for MKM-883-1
|
|
To remove transmission in conjunction with MKM-883-2
|
|
|
|
KM-899
|
Remover / Installer
|
|
Removal and installation of converter with M10 thread.
|
|
|
|
KM-910
|
Transmission Holder
|
|
To hold transmission in conjunction with KM-113-2
|
|
|
|
KM-924
|
Blanking Plugs
|
|
To close off fluid cooler lines
|
|
|
|
KM-962-A
|
Tester
|
|
To test and adjust selector lever position switch
|
|
|
|
KM-994
|
Adapter
|
|
Sleeve adapter for compressed air gun
|
|
|
|
KM-6001-B
|
Engine Mount
|
|
Centring the engine when removing the transmission
|
|
|
|
KM-6037
|
Adapter
|
|
Turning the differential to check bearing pre-tensioning in
conjunction with MKM-536-A
|
|
|
|
KM-6326
|
Blanking Plugs
|
|
Plugging oil cooler line (yellow) and transmission aperture
(green)
|
|
|
|
KM-6328
|
Adapter Piece
|
|
Pulling oil pump seal ring from converter housing together with
KM-328-B and KM-469-A
|
|
|
|
KM-6329
|
Adapter
|
|
Checking fluid pressure together with KM-498-B
|
|
|
|
KM-6388
|
Bracket
|
|
Securing torque converter so it does not fall out
|
|
|
|
KM-J-7004
|
Slide Hammer
|
|
To drive out fluid pump seal ring with KM-586
|
|
|
|
KM-J-23078-A
|
Clutch Tensioner
|
|
Dismantling and assembly of various clutches
|
|
|
|
KM-J-26941
|
Remover
|
|
Roller bearing from converter housing with KM-313 and KM-483
|
|
|
|
KM-J-41623-B
|
Release Tool
|
|
Releasing oil cooler line and radiator
|
|
|
|
DT-47648
|
Transmission holder
|
|
Removing, installing and holding transmission
|
|
|
|
