Test
|
Work Order Description
|
Nominal Value
|
T001
|
Check: Diagnostic Trouble Code stored
|
Is at least one of the following trouble codes with status PRESENT stored?
P1726
Select Motor Malfunction
P1729
Select Motor Electrical Malfunction
|
|
|
T002
|
Check: Short to Ground of Voltage Supply Circuit
|
- Ignition OFF
- Disconnect wiring harness connector from:
Y144.1 Motor - Transmission, Select and A112 Control Unit - Transmission (Wiring Harness Connector XC14 )
- Measure resistance between the following terminals:
Y144.1 Motor - Transmission, Select Wiring harness connector (wiring harness side) terminal 1 & Ground
|
greater than 500 kOhm
|
|
|
T003
|
Check: Interruption of Voltage Supply Circuit
|
- Measure resistance between the following terminals:
Y144.1 Motor - Transmission, Select Wiring harness connector (wiring harness side) terminal 1 & A112 Control Unit - Transmission Wiring harness connector (wiring harness side) terminal 117 (XC14)
|
less than 5 Ohm
|
|
|
T004
|
Check: Short to Ground of Voltage Supply Circuit
|
- Measure resistance between the following terminals:
Y144.1 Motor - Transmission, Select Wiring harness connector (wiring harness side) terminal 6 & Ground
|
greater than 500 kOhm
|
|
|
T005
|
Check: Interruption of Voltage Supply Circuit
|
- Measure resistance between the following terminals:
Y144.1 Motor - Transmission, Select Wiring harness connector (wiring harness side) terminal 6 & A112 Control Unit - Transmission Wiring harness connector (wiring harness side) terminal 114 (XC14)
|
less than 5 Ohm
|
|
|
T006
|
Check: Diagnostic Trouble Code stored
|
Is the following Trouble Code stored?
P1726
Select Motor Circuit Open or Low Voltage
|
|
|
T007
|
Check: Short to Ground of Voltage Supply Circuit
|
- Ignition OFF
- Disconnect wiring harness connector from:
Y144.1 Motor - Transmission, Select and A112 Control Unit - Transmission (Wiring Harness Connector XC14 )
- Measure resistance between the following terminals:
Y144.1 Motor - Transmission, Select Wiring harness connector (wiring harness side) terminal 3 & Ground
|
greater than 500 kOhm
|
|
|
T008
|
Check: Interruption of Voltage Supply Circuit
|
- Measure resistance between the following terminals:
Y144.1 Motor - Transmission, Select Wiring harness connector (wiring harness side) terminal 3 & A112 Control Unit - Transmission Wiring harness connector (wiring harness side) terminal 119 (XC14)
|
less than 5 Ohm
|
|
|
T009
|
Check: Component
|
- Connect wiring harness connector to:
A112 Control Unit - Transmission (Wiring Harness Connector XC14 )
- Ignition ON
- Measure voltage between the following terminals:
Y144.1 Motor - Transmission, Select Wiring harness connector (wiring harness side) terminal 3 & Ground
|
greater than 11 V
|
|
|
T010
|
Check: Diagnostic Trouble Code stored
|
Is the following Trouble Code stored?
P1726
Select Motor Circuit High Voltage
|
|
|
T011
|
Check: Circuit Interruption of Ground Circuit
|
- Ignition OFF
- Disconnect wiring harness connector from:
Y144.1 Motor - Transmission, Select and A112 Control Unit - Transmission (Wiring Harness Connector XC14 )
- Measure resistance between the following terminals:
Y144.1 Motor - Transmission, Select Wiring harness connector (wiring harness side) terminal 2 & A112 Control Unit - Transmission Wiring harness connector (wiring harness side) terminal 120 (XC14)
|
less than 5 Ohm
|
|
|
T012
|
Check: Diagnostic Trouble Code stored
|
Is the following Trouble Code stored?
P1726
Select Motor Speed Signal Circuit Malfunction
|
|
|
T013
|
Check: Short to Voltage of Signal Circuit
|
- Ignition OFF
- Disconnect wiring harness connector from:
Y144.1 Motor - Transmission, Select and A112 Control Unit - Transmission (Wiring Harness Connector XC14 )
- Ignition ON
- Measure voltage between the following terminals:
Y144.1 Motor - Transmission, Select Wiring harness connector (wiring harness side) terminal 5 & Ground
|
less than 0.3 V
|
|
|
T014
|
Check: Short to Ground of Signal Circuit
|
- Ignition OFF
- Measure resistance between the following terminals:
Y144.1 Motor - Transmission, Select Wiring harness connector (wiring harness side) terminal 5 & Ground
|
greater than 500 kOhm
|
|
|
T015
|
Check: Interruption of Signal Circuit
|
- Measure resistance between the following terminals:
Y144.1 Motor - Transmission, Select Wiring harness connector (wiring harness side) terminal 5 & A112 Control Unit - Transmission Wiring harness connector (wiring harness side) terminal 106 (XC14)
|
less than 5 Ohm
|
|
|
T016
|
Check: Diagnostic Trouble Code stored
|
Is the following Trouble Code stored?
P1726
Select Motor Direction Signal Circuit Malfunction
|
|
|
T017
|
Check: Short to Voltage of Signal Circuit
|
- Ignition OFF
Disconnect wiring harness connector from: Y144.1 Motor - Transmission, Select (Wiring Harness Connector XC14 ) and A112 Control Unit - Transmission
- Ignition ON
- Measure voltage between the following terminals:
Y144.1 Motor - Transmission, Select Wiring harness connector (wiring harness side) terminal 4 & Ground
|
less than 0.3 V
|
|
|
T018
|
Check: Short to Ground of Signal Circuit
|
- Ignition OFF
- Measure resistance between the following terminals:
Y144.1 Motor - Transmission, Select Wiring harness connector (wiring harness side) terminal 4 & Ground
|
greater than 500 kOhm
|
|
|
T019
|
Check: Interruption of Signal Circuit
|
- Measure resistance between the following terminals:
Y144.1 Motor - Transmission, Select Wiring harness connector (wiring harness side) terminal 4 & A112 Control Unit - Transmission Wiring harness connector (wiring harness side) terminal 107 (XC14)
|
less than 5 Ohm
|
|
|
T020
|
Check: Diagnostic Trouble Code stored
|
Is the following Trouble Code stored?
P1730
Select Motor Mechanical Malfunction
|
|
|