vauxhall Workshop Repair Guides

Vauxhall Workshop Service and Repair Manuals

ABOUT US
C-009 Solenoid Valve Shift 1 Circuit > < C-007 Clutch Solenoid Valve Circuit

Astra H

C-008 - Selector Position Switch Circuit

Test

Work Order Description

Nominal Value
T001

Check: Interruption of Voltage Supply Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    A163 Switch - Selector Lever
  • Ignition ON
  • Measure voltage between the following terminals:
    A163 Switch - Selector Lever
    Wiring harness connector (wiring harness side) terminal 7
    &
    Ground

greater than 11 V
Voltage Measurement Current Value: V
Yes: No:
T002

Check: Interruption of Voltage Supply Circuit
  • Measure voltage between the following terminals:
    A163 Switch - Selector Lever
    Wiring harness connector (wiring harness side) terminal 1
    &
    A163 Switch - Selector Lever
    Wiring harness connector (wiring harness side) terminal 7

greater than 11 V
Voltage Measurement Current Value: V
Yes: No:
T003

Check: Short to Voltage of Signal Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    A112 Control Unit - Transmission
    (Wiring Harness Connector XC82 )
  • Ignition ON
  • Measure voltage between the following terminals:
    A163 Switch - Selector Lever
    Wiring harness connector (wiring harness side) terminal 12
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T004

Check: Short to Ground of Signal Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    A112 Control Unit - Transmission
    (Wiring Harness Connector XC82 )
  • Measure resistance between the following terminals:
    A163 Switch - Selector Lever
    Wiring harness connector (wiring harness side) terminal 12
    &
    Ground

greater than 500 kOhm
Resistance Measurement Current Value: kOhm
Yes: No:
T005

Check: Interruption of Signal Circuit
  • Measure resistance between the following terminals:
    A163 Switch - Selector Lever
    Wiring harness connector (wiring harness side) terminal 12
    &
    A112 Control Unit - Transmission
    Wiring harness connector (wiring harness side) terminal 14 (XC82)

less than 5 Ohm
Resistance Measurement Current Value: Ohm
Yes: No:
T006

Check: Short to Voltage of Signal Circuit
  • Ignition ON
  • Measure voltage between the following terminals:
    A163 Switch - Selector Lever
    Wiring harness connector (wiring harness side) terminal 6
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T007

Check: Short to Ground of Signal Circuit
  • Ignition OFF
  • Measure resistance between the following terminals:
    A163 Switch - Selector Lever
    Wiring harness connector (wiring harness side) terminal 6
    &
    Ground

greater than 500 kOhm
Resistance Measurement Current Value: kOhm
Yes: No:
T008

Check: Interruption of Signal Circuit
  • Measure resistance between the following terminals:
    A163 Switch - Selector Lever
    Wiring harness connector (wiring harness side) terminal 6
    &
    A112 Control Unit - Transmission
    Wiring harness connector (wiring harness side) terminal 18 (XC82)

less than 5 Ohm
Resistance Measurement Current Value: Ohm
Yes: No:


Result

Cause Of Fault
E001 Result: Defective Component
  • Defective component:
    A163 Switch - Selector Lever
    or
    A112 Control Unit - Transmission
E002 Result: Interruption
  • Circuit interruption between:
    A163 Switch - Selector Lever
    Wiring harness connector (wiring harness side) terminal 6
    &
    A112 Control Unit - Transmission
    Wiring harness connector (wiring harness side) terminal 18 (XC82)
E003 Result: Short to Ground
  • Short circuit to ground between:
    A163 Switch - Selector Lever
    Wiring harness connector (wiring harness side) terminal 6
    &
    A112 Control Unit - Transmission
    Wiring harness connector (wiring harness side) terminal 18 (XC82)
E004 Result: Short to Voltage
  • Short circuit to voltage between:
    A163 Switch - Selector Lever
    Wiring harness connector (wiring harness side) terminal 6
    &
    A112 Control Unit - Transmission
    Wiring harness connector (wiring harness side) terminal 18 (XC82)
E005 Result: Interruption
  • Circuit interruption between:
    A163 Switch - Selector Lever
    Wiring harness connector (wiring harness side) terminal 12
    &
    A112 Control Unit - Transmission
    Wiring harness connector (wiring harness side) terminal 14 (XC82)
E006 Result: Short to Ground
  • Short circuit to ground between:
    A163 Switch - Selector Lever
    Wiring harness connector (wiring harness side) terminal 12
    &
    A112 Control Unit - Transmission
    Wiring harness connector (wiring harness side) terminal 14 (XC82)
E007 Result: Short to Voltage
  • Short circuit to voltage between:
    A163 Switch - Selector Lever
    Wiring harness connector (wiring harness side) terminal 12
    &
    A112 Control Unit - Transmission
    Wiring harness connector (wiring harness side) terminal 14 (XC82)
E008 Result: Interruption
  • Circuit interruption between:
    A163 Switch - Selector Lever
    Wiring harness connector (wiring harness side) terminal 1
    &
    Ground
E009 Result: Interruption
  • Circuit interruption between:
    FE29 Fuse
    Output contact
    &
    A163 Switch - Selector Lever
    Wiring harness connector (wiring harness side) terminal 7

or

  • Defective component:
    X125 Underhood Electronic Module





C-009 Solenoid Valve Shift 1 Circuit > < C-007 Clutch Solenoid Valve Circuit