|
Special Service Tools
Special Service Tools
|
|
KM-135
|
Adapter
|
|
Measure engine oil pressure in conjunction with KM-498-B
|
|
KM-194-E
|
Spark plug key
|
|
Removing and installing spark plugs with WAF 16
|
|
KM-263-B
|
Engine bridge
|
|
Holding the engine
|
|
KM-328-B
|
Remover
|
|
Removing the crankshaft needle bearing
|
|
KM-340-G
|
Valve seat milling set
|
|
Milling, correcting valve seat
|
|
KM-348
|
Compressing valve springs, cylinder head dismantled
|
|
|
|
|
Special Service Tools (continued)
|
KM-412
|
Engine assembly stand
|
|
Holding dismantled engine
|
|
KM-412-3
|
Adapter
|
|
Holding engine in conjunction with KM-412
|
|
KM-417
|
Assembly sleeves
|
|
Inserting crankshaft sealing ring into oil pump housing
|
|
KM-422
|
Installer
|
|
Inserting sealing ring into camshaft
|
|
KM-427
|
Remover and installer
|
|
Hammering the centring punches into the cylinder block
|
|
KM-460-B
|
Remover
|
|
Pushing the drive shafts out of the transmission
|
|
|
|
|
Special Service Tools (continued)
|
KM-468-B
|
Holding wrench
|
|
Supporting the wheel hub
|
|
KM-470-B
|
Angled tightening wrench
|
|
Tightening the cylinder head bolts
|
|
KM-471
|
Adapter
|
|
Testing the cooling system under pressure in conjunction with
cooling system tester
|
|
KM-498-B
|
Oil pressure gauge
|
|
Checking engine oil pressure in conjunction with KM-135
|
|
KM-517-B
|
Flywheel holder
|
|
Locking the flywheel
|
|
MKM-596-A
|
Measuring instrument
|
|
Measuring the oil temperature
|
Special Service Tools (continued)
|
|
|
|
MKM-604-D
|
Torx bit and socket set
|
|
Removing and installing Torx bolts
|
|
KM-609
|
Electronics Kit
|
|
Diagnosis of electrical and electronic systems
|
|
MKM-610
|
Torque wrench 1/2" drive
|
|
Range 30 to 130 Nm
|
|
MKM-611
|
Torque wrench 3/8" drive
|
|
Range 10 to 60 Nm
|
|
KM-634
|
Remover and installer
|
|
Removing and installing piston bolts
|
|
KM-640
|
Diagnostic switch
|
|
Triggering release of flashing code
|
|
|
|
|
Special Service Tools (continued)
|
KM-652
|
Flywheel holder
|
|
Locking flywheel or drive disc
|
|
KM-653-A
|
Adapter
|
|
Tensioning valve spring in conjunction with KM-348
|
|
KM-658
|
Installer
|
|
Installation of the rear crankshaft sealing ring
|
|
MKM-667
|
Pressure and vacuum pump
|
|
Checking the vacuum unit for leaks
|
|
MKM-669
|
Torque wrench 1/2" drive
|
|
Range 50 to 300 Nm
|
|
KM-726-A
|
Oil filter wrench
|
|
Removing and installing the oil filter
|
|
|
|
|
Special Service Tools (continued)
|
KM-728-A
|
Remover, installer
|
|
Removing and installing the knock sensor
|
|
KM-734
|
Guide pin
|
|
Centring the clutch disc
|
|
KM-805
|
Reamer 6 mm
|
|
Roughening the valve guide, oversize 0.075 mm
|
|
KM-835-A
|
Installer
|
|
Installing the valve stem seal
|
|
MKM-836
|
Remover
|
|
Removing spark plug boot
|
|
KM-840
|
Remover
|
|
Removing the valve stem seal
|
|
|
|
|
Special Service Tools (continued)
|
KM-845
|
Suction tool
|
|
Removing and installing the hydraulic valve lifters
|
|
KM-852
|
Locking tool
|
|
Locking the camshaft pulleys
|
|
MKM-874
|
Precision multi-meter
|
|
Checking electrical/electronic components
|
|
MKM-883-1
|
Engine bridge
|
|
Holding the engine (alternative to KM-263-B)
|
|
MKM-889
|
Automatic valve spring lifter
|
|
Removing and installing the valve springs
|
|
KM-902
|
Remover
|
|
Removing the axle shafts
|
Special Service Tools (continued)
|
|
|
|
KM-904
|
Base frame
|
|
Removing and installing various vehicle components with
additional adapters
|
|
KM-911
|
Flywheel holder
|
|
Locking flywheel or drive disc
|
|
KM-956-1
|
Clamp with handle
|
|
Holding the camshaft pulleys to release/tighten the fastening
bolts in conjunction with KM-6347
|
|
KM-2358
|
Engine-lifting straps
|
|
Removing and installing the engine
|
|
KM-6054
|
Holding the engine
|
|
Removing and installing the engine
|
|
KM-6347
|
Bracket
|
|
Holding the camshaft pulleys to release/tighten the fastening
bolts in conjunction with KM-956-1
|
Special Service Tools (continued)
|
|
|
|
KM-J-26792
|
Test spark plug
|
|
Testing ignition sparks
|
|
KM-J-34730-91
|
Pressure testing unit
|
|
Checking the fuel pressure
|
|
KM-J-37228
|
Separating tool
|
|
For removing the sheet metal oil pan
|
|
|
|
