|
C-10, Park/Neutral Switch Circuit |
|
Test |
Work Order Description |
Nominal Value |
|
T01 |
Check: Vehicle Configuration |
|
|
|
Is the following information correct for the actual vehicle? AF 13/20/22 Electronic 4-Speed Automatic Transmission
|
|
|
|
Yes: T02 |
No: T10 |
|
T02 |
Check: Vehicle Configuration |
|
|
|
Is the following information correct for the actual vehicle? Astra-F
|
|
|
|
Yes: T03 |
No: T07 |
|
T03 |
Check: Interruption of Signal Circuit |
|
|
|
• Ignition OFF • Disconnect wiring harness connector from:
X9 Instrument Panel & Multec 9P • Measure resistance between the following terminals:
X9 Instrument Panel & Multec 9P
Wiring Harness Connector (wiring harness side) Terminal 9
&
Ground • Selector lever in position P-N
|
less than 5 Ohm |
|
|
Yes: T04 |
No: T06 |
|
T04 |
Check: Short to Ground of Signal Circuit |
|
|
|
• Measure resistance between the following terminals:
X9 Instrument Panel & Multec 9P
Wiring Harness Connector (wiring harness side) Terminal 9
&
Ground
Selector lever in position R-D-3-2-1
|
greater than 100 kOhm |
|
|
Yes: T05 |
No: T06 |
|
T05 |
Check: Short to Ground/Interruption of Signal Circuit |
|
|
|
• Ignition ON • Measure voltage between the following terminals:
X9 Instrument Panel & Multec 9P
Wiring Harness Connector (control unit side) Terminal 9
&
Ground
|
greater than 11 V |
|
|
Yes: E01 |
No: E02 |
|
T06 |
Check: Adjustment |
|
|
|
• Check adjustment of the following component (refer to Service Manual):
S10 Switch - Automatic Transmission
|
Adjustment okay? |
|
|
Yes: E03 |
No: E04 |
|
T07 |
Check: Interruption of Signal Circuit |
|
|
|
• Ignition OFF • Disconnect wiring harness connector from:
X4 Instrument Panel & Multec 4P • Measure resistance between the following terminals:
X4 Instrument Panel & Multec 4P
Wiring Harness Connector (wiring harness side) Terminal 1
&
Ground • Selector lever in position P-N
|
less than 5 Ohm |
|
|
Yes: T08 |
No: T06 |
|
T08 |
Check: Short to Ground of Signal Circuit |
|
|
|
• Measure resistance between the following terminals:
X4 Instrument Panel & Multec 4P
Wiring Harness Connector (wiring harness side) Terminal 1
&
Ground • Selector lever in position R-D-3-2-1
|
greater than 100 kOhm |
|
|
Yes: T09 |
No: T06 |
|
T09 |
Check: Short to Ground/Interruption of Signal Circuit |
|
|
|
• Ignition ON • Measure voltage between the following terminals:
X4 Instrument Panel & Multec 4P
Wiring Harness Connector (control unit side) Terminal 1
&
Ground
|
greater than 11 V |
|
|
Yes: E01 |
No: E02 |
|
T10 |
Check: Programming |
|
|
|
• Diagnostic Tester Data List Parameter
TRANSM. CODING
|
MT |
|
|
Yes: E05 |
No: T11 |
|
T11 |
Check: Programming |
|
|
|
• Are you using the latest version of control unit software?
|
|
|
|
Yes: E06 |
No: E07 |
