C-07, Manifold Absolute Pressure Solenoid Circuit
|
C-07, Manifold Absolute Pressure Solenoid Circuit |
|
Test |
Work Order Description |
Nominal Value |
|
T01 |
Check: Short to Voltage/Ground/Interruption of Voltage Supply |
|
|
|
• Ignition OFF • Disconnect wiring harness connector from:
P23 Sensor - Absolute Pressure, Intake Manifold • Ignition ON • Measure voltage between the following terminals:
P23 Sensor - Absolute Pressure, Intake Manifold
Wiring Harness Connector Terminal C
&
Ground
|
4.8 ... 5.2 V |
|
|
Yes: T02 |
No: T05 |
|
T02 |
Check: Short to Voltage/Interruption of Ground Circuit |
|
|
|
• Measure voltage between the following terminals:
P23 Sensor - Absolute Pressure, Intake Manifold
Wiring Harness Connector Terminal A
&
P23 Sensor - Absolute Pressure, Intake Manifold
Wiring Harness Connector Terminal C
|
4.8 ... 5.2 V |
|
|
Yes: T03 |
No: E04 |
|
T03 |
Check: Short to Voltage of Signal Circuit |
|
|
|
• Diagnostic Tester Data List Parameter
MAP SENSOR
|
less than 0.1 bar
less than 0.2 V |
|
|
Yes: T04 |
No: E03 |
|
T04 |
Check: Short to Ground/Interruption of Signal Circuit |
|
|
|
• Connect fused jumper wire to:
P23 Sensor - Absolute Pressure, Intake Manifold
Wiring Harness Connector Terminal B
&
P23 Sensor - Absolute Pressure, Intake Manifold
Wiring Harness Connector Terminal C • Diagnostic Tester Data List Parameter
MAP SENSOR
|
greater than 0.95 bar
greater than 4.8 V |
|
|
Yes: E01 |
No: E02 |
|
T05 |
Check: Short to Voltage/Ground/Interruption of Voltage Supply |
|
|
|
• Measure voltage between the following terminals:
P23 Sensor - Absolute Pressure, Intake Manifold
Wiring Harness Connector Terminal C
&
Ground • Disconnect each of the following components/control units consecutively from the wiring harness and repeat the measurement each time:
Only X 14 SZ, X 16 SZR, Astra-F X 14 XE :
Y18 Solenoid Valve - Exhaust Gas Recirculation
P34 Potentiometer - Throttle Valve
Only Corsa-B/Tigra, X 14 XE/X 16 XE :
X10 Multec & Valve, Injection
Only Astra-F, X16 XEL :
X10 Multec & Valve, Injection
Y18 Solenoid Valve - Exhaust Gas Recirculation
|
4.8 ... 5.2 V |
|
|
Yes: E05 |
No: E06 |
|
C-07, Manifold Absolute Pressure Solenoid Circuit |
|
Result |
Cause Of Fault |
|
E01 |
• Defective component:
Vacuum hose
or
P23 Sensor - Absolute Pressure, Intake Manifold Note: Check the hoses for leakage or blockage before replacing the component. |
|
|
|
|
E02 |
• Short circuit to ground/interruption of circuit between:
P23 Sensor - Absolute Pressure, Intake Manifold
Wiring Harness Connector Terminal B
&
K57 Control Unit - Multec
Wiring Harness Connector Terminal A7 or • Defective component:
K57 Control Unit - Multec |
|
|
|
|
E03 |
• Short circuit to voltage between:
P23 Sensor - Absolute Pressure, Intake Manifold
Wiring Harness Connector Terminal B
&
K57 Control Unit - Multec
Wiring Harness Connector Terminal A7 or • Defective component:
K57 Control Unit - Multec |
|
|
|
|
E04 |
• Short circuit to voltage/interruption of circuit between:
P23 Sensor - Absolute Pressure, Intake Manifold
Wiring Harness Connector Terminal A
&
K57 Control Unit - Multec
Wiring Harness Connector Terminal D15 or • Defective component:
K57 Control Unit - Multec |
|
|
|
|
E05 |
• If the nominal value is reached during one of the measurements, the component/control unit that has been disconnected immediately before that measurement is defective. |
|
|
|
|
E06 |
• If the nominal value is not reached with any of the measurements, this indicates that one of the following faults is present:
Short to voltage/ground/interruption of circuit between:
P23 Sensor - Absolute Pressure, Intake Manifold
Wiring Harness Connector Terminal C
&
K57 Control Unit - Multec
Wiring Harness Connector Terminal D8
or
Defective component:
K57 Control Unit - Multec |
|
|
|
|
