Special Service Tools
Special Service Tools
|
KM-128-A
|
Test unit
|
Test V-belt tension
|
KM-135
|
Adapter
|
Measure engine oil pressure in conjunction with KM-498-B
|
KM-263-B
|
Engine bridge
|
Holding the engine
|
KM-328-B
|
Remover
|
Removing the crankshaft needle bearing in conjunction with
KM-469-A
|
KM-340-G
|
Valve seat milling set
|
Milling, correcting valve seat
|
KM-348
|
Spring tensioner
|
Compressing valve springs, cylinder head dismantled
|
|
|
|
Special Service Tools (continued)
KM-352
|
Insertion sleeve
|
Assembly of valve stem seals
|
KM-412
|
Engine assembly stand
|
Holding dismantled engine
|
KM-412-3
|
Adapter
|
Holding engine in conjunction with KM-412
|
KM-417
|
Assembly sleeves
|
Inserting crankshaft sealing ring into oil pump housing
|
KM-419
|
Distance gauge
|
Checking valve projection after machining valve seat
|
KM-421-A
|
Adjusting spanner
|
Adjusting toothed belt tension
|
|
|
|
Special Service Tools (continued)
KM-422
|
Installer
|
Inserting sealing ring into camshaft
|
KM-427
|
Remover and installer
|
Hammering the centring punches into the cylinder block
|
KM-460-B
|
Removers
|
Pushing the axle shaft out of the transmission
|
KM-470-B
|
Angled tightening wrench
|
Tightening cylinder head bolts
|
KM-471
|
Adapter
|
Testing cooling system under pressure in conjunction with
cooling system tester
|
KM-498-B
|
Oil pressure gauge
|
Checking engine oil pressure in conjunction with KM-135
|
Special Service Tools (continued)
|
|
|
KM-517-B
|
Flywheel holder
|
Locking flywheel with the transmission installed
|
KM-526-A
|
Clamping bracket
|
Clutch assembly with 3 clamps
|
KM-565-A
|
Remover, installer
|
Removing and installing cam followers and hydraulic valve
lifters
|
MKM-588-A
|
Pressure gauge for performing checks
|
Checking fuel pressure
|
MKM-596-A
|
Measuring instrument
|
Measuring oil temperature
|
MKM-604-D
|
Torx bit and socket set
|
Removing and installing Torx bolts
|
|
|
|
Special Service Tools (continued)
KM-609
|
Electronics kit I
|
Diagnosis of electrical and electronic systems
|
MKM-610
|
Torque wrench 1/2" drive
|
Range 30-130 Nm
|
MKM-611
|
Torque wrench 3/8" drive
|
Range 10-60 Nm
|
KM-632-A
|
Remover, installer
|
Tensioning clutch assembly, engine removed
|
KM-634
|
Remover, installer
|
Removing and installing piston bolts
|
KM-640
|
Diagnostic switch
|
Triggering release of flashing code, engines with
self-diagnosis
|
|
|
|
Special Service Tools (continued)
KM-652
|
Flywheel holder
|
Locking flywheel
|
KM-658
|
Installer
|
Installing rear crankshaft sealing ring
|
KM-664
|
Reamer set 7 mm
|
Roughening the valve guide
|
MKM-667
|
Pressure and vacuum pump
|
Checking the vacuum unit for leaks
|
MKM-669
|
Torque wrench 1/2" drive
|
Range 50-300 Nm
|
KM-717
|
Puller
|
Pulling out spark plug boot
|
|
|
|
Special Service Tools (continued)
KM-726-A
|
Oil filter wrench
|
Removing and installing the oil filter
|
KM-728-A
|
Wrench for removing and installing
|
Removing and installing the knock sensor on X 12 SZ and X 14
SZ
|
KM-734
|
Guide pin
|
Centring the clutch disc
|
KM-834-A
|
Remover, installer
|
Removing and installing heat protection sleeves
|
MKM-874
|
Precision multi-timer
|
Checking electrical/electronic components
|
MKM-883-1
|
Engine bridge
|
Holding the engine
|
|
|
|
Special Service Tools (continued)
KM-902
|
Remover
|
Removing the axle shafts
|
KM-904
|
Base frame
|
Removing and installing various vehicle components
|
KM-911
|
Flywheel holder
|
Locking flywheel/drive disc
|
KM-937
|
Extension
|
Removing drive shaft with KM-460-B
|
KM-956-1
|
Clamp with handle
|
Holding the camshaft pulleys to release/tighten the fastening
bolts in conjunction with KM-6347
|
KM-2358
|
Engine-lifting straps
|
Removing and installing the engine
|
|
|
|
Special Service Tools (continued)
KM-6054
|
Holding the engine
|
Removing and installing the engine
|
KM-6347
|
Bracket
|
Holding the camshaft pulleys to release/tighten the fastening
bolts in conjunction with KM-956-1
|
KM-J-26792
|
Test spark plug
|
Testing ignition sparks
|
KM-J-34730-91
|
Pressure testing unit
|
Checking the fuel pressure (Multec-M)
|
KM-J-37228
|
Separating tool
|
For removing the sheet metal oil pan
|
|
|
|