Special Service Tools
KM- 128-A Tension Gauge
To check the V-belt tension
|
|
KM - 135 Adapter for
KM - 498 - B
To measure the engine oil pressure
|
|
KM-235-D Ring Installer
To install the crankshaft bearing and seal ring
|
|
KM-252-2-A Cables (Length 850 cm)
To remove and install the engine
|
|
KM - 253 * Reamer 0.075 mm
Oversize
KM - 254 * Reamer 0.150 mm
Oversize
KM - 255 * Reamer 0.250 mm
Oversize
To ream the valve guide bore
* No longer available
|
|
KM-263-B Lifter / Holder
To hold the engine in conjunction with
KM - 252 - 2 A
|
|
KM-328-B Remover
To remove the crankshaft needle bearing in conjunction with
KM - 469 - A
|
|
KM - 334 (S - 1254) Installer
To remove and install the fan bracket bearing in conjunction
with KM - 258
|
|
KM-340-C Cutter Set
To grind and to correct the valve seat
|
|
KM - 348 Spring Compressor
To compress the valve spring with the cylinder head removed
|
|
KM - 352 Installer
To install the valve stem sealing
|
|
KM - 412 Engine Overhaul Stand
To hold the removed engine
|
|
KM-412- 10 Adapter
To hold engine in conjunction with KM - 412
|
|
KM - 417 Installer
To install crankshaft seal ring into oil pump housing
|
|
KM-419 Distance Gauge
To check protrusion of valve guide after reworking valve
seat
|
|
KM-421 -A Adjusting Wrench
To adjust toothed belt tension
|
|
KM - 422 Remover / Installer
To install seal ring into camshaft carrier
|
|
KM - 427 Remover / Installer
To remove and install piston pin
|
|
KM-469-A Remover / Installer
To remove and install crankshaft needle bearing and seal
ring in conjunction with KM - 328 - B
|
|
KM-470-B Angular Torque Wrench
To tighten cylinder head screws
|
|
KM-498-B Pressure Gauge
To check the engine oil pressure in conjunction with
KM - 135
|
|
KM-510-A Tension Gauge
To check and adjust the toothed belt tension
For engines without automatic toothed belt tension
roller
|
|
KM - 517 Locking Device
To lock the flywheel
|
|
KM-526-A Clamp Set
To grip clutch assembly with 3 clamps
|
|
KM-556-A Remover / Installer
To remove the transmission drive shaft, bearing bushings for
Delco -Remy starter
|
|
KM - 564 Remover / Installer
To install the transmission drive shaft
|
|
KM - 565 Remover / Installer
To remove and install rocker arm and valve play compensators
|
|
KM-566-1 Universal Checking Adapter
To check L-Jetronic in conjunction with
KM - 566 - 10 and MKM - 587 - A
|
|
KM - 566 - 10 Checking Cable
To check L-Jetronic in conjunction with
KM - 566 - 1 and MKM - 587 - A
|
|
MKM-587-A Multimeter
Measurements of vehicle electronics
|
|
MKM - 588 Pressure Gauge
To check fuel pressure
|
|
MKM - 596 Gauge
To measure oil temperature (exhaust gas checks)
|
|
MKM - 597 Removing Pliers (replaced by
KM - 717)
To remove spark plug connectors
|
|
MKM-604-B Torx Bit and Socket Set
To remove and install Torx bolts
|
|
KM - 605 Adapter
To connect CO tester to vehicles with open loop catalytic
converter.
|
|
KM - 609 Electronic Kit I
Diagnosis of electrical and electronic systems
|
|
MKM-610 Torque Wrench 1/2" Drive
Measuring range 30 - 130 Nm/22 - 96
lbf. ft.
|
|
MKM - 611 Torque Wrench 3/8" Drive
Measuring range 10 - 60 Nm/7 - 44
lbf. ft.
|
|
KM-611 Remover / Installer
To remove and install piston pin
|
|
KM - 639 Remover / Installer
To remove and install idle cut-off valve for 2E 3
carburettor
|
|
KM - 640 Diagnostic Switch
To trigger the blink code readout on vehicles with
self-diagnosis
|
|
KM - 652 Locking Device
To lock flywheel
|
|
MKM - 667 Pressure and Vacuum Pump
To check vacuum cell for leaks
|
|
KM - 717 Remover Pliers
Remover pliers for spark plug connectors
|
|
KM - J - 26792 Spark Tester
To check ignition spark
|
|
KM - J - 34730 - 91 Fuel
Pressure Gauge
To check fuel pressure
|
|