No.
|
TECH 1-DISPLAY
|
Conditions for
Checking
|
Nominal Value
|
Trouble Codes
|
Terminal
|
|
08
|
BRAKE SWITCH 2
|
Ignition ON
|
|
37
|
31,
18
|
|
|
|
Brake not actuated
|
INACTIVE 12V
|
|
|
|
|
|
Brake actuated
|
ACTIVE 0V
|
|
|
|
|
|
|
|
|
|
|
Note:
Test steps 07 and 08 are divided into three parts:
a) If
trouble code 37 has been stored: carry out above data list parameter tests
b) If the
nominal values for data list parameter 07 were not attained: start
trouble-shooting at data list parameter 07
c) If the
nominal values for data list parameter 08 were not attained: start
trouble-shooting at data list parameter 08
|
|
Notes on Trouble-shooting:
|
Nominal Value:
|
Cause of Fault:
(If nominal value is not
attained)
|
Trouble-shooting for data list parameter 07:
|
|
|
|
· Check bulb for brake lamps H9, H10, H36
and fuse F2
|
|
· Replace defective parts
|
|
|
|
If fuse F2 is defective, insert new fuse and repeat above
data list parameter tests. If this destroys the fuse again, proceed with the
following diagnostic step.
|
|
· Disconnect wiring harness plug from
brake lamp switch S8
· Ignition ON
· Using multimeter, measure voltage
from: wiring
harness plug for brake lamp switch S8 Ter. 1
to: ground
|
greater than 11 V
|
· Fuse F2 defective
· Short circuit to ground / circuit
interruption
from: wiring
harness plug for switch S1 Ter. 15
to: wiring
harness plug for brake lamp switch S8 Ter. 1
· Short circuit to ground
from: wiring
harness plug for switch S1 Ter. 15
to: wiring
harness plug for control unit, MID U16/ TID U15 Ter. 16
· Short circuit to ground
from: fuse
socket F2
to: wiring
harness plug for hazard warning lamps switch S52 Ter. 13
· Fault in circuit, MID U16/ TID U15
(see Checking Procedures, MID/ TID)
· Hazard warning lamps switch S52
defective
|
|
· Ignition ON
· TECH 1 data list no. 07
|
INACTIVE 0V
(brake lamps OFF)
|
Disconnect following control units/ components from
wiring harness consecutively:
· Control unit, bulb control P25
· Control unit, automatic transmission
K85
· Control unit, ABS U4.8
· Electric selector lever pawl K102
(Japan only)
· Brake lamps H9, H10 and H36
While doing this, repeat the same test as described on the
left each time a control unit or component is disconnected from the wiring
harness.
If the nominal value is attained for one control unit/
component, the fault is in the circuit of the previously disconnected control
unit or component.
|
|
|
|
All components except DDE 2.1 control unit K70
disconnected from wiring harness but nominal value not attained:
· Short circuit to voltage
from: wiring
harness plug for brake lamp switch S8 Ter. 2
to: wiring
harness plug of one of the above mentioned control units/ components
· DDE 2.1 control unit K70 defective
|
|
· Jumper wiring harness plug for brake
lamp switch S8
from: wiring
harness plug for brake lamp switch S8 Ter. 1
to: wiring
harness plug for brake lamp switch S8 Ter. 2
· TECH 1 data list no. 07
|
ACTIVE 12V
|
Disconnect following control units/ components from
wiring harness consecutively:
· Control unit, bulb control P25
· Control unit, automatic transmission
K85
· Control unit, ABS U4.8
· Electric selector lever pawl K102
(Japan only)
· Brake lamps H9, H10 and H36
While doing this, repeat the same test as described on the
left each time a control unit or component is disconnected from the wiring
harness.
|
|
|
|
If the nominal value is attained for one control unit/
component, the fault is in the circuit of the previously disconnected control
unit or component.
All components except DDE 2.1 control unit K70
disconnected from wiring harness but nominal value not attained:
· Short circuit to ground
from: wiring
harness plug for brake lamp switch S8 Ter. 2
to: wiring
harness plug of one of the above mentioned control units/ components
· Circuit interruption
from: wiring
harness plug for brake lamp switch S8 Ter. 2
to: wiring
harness plug for DDE 2.1 control unit K70 Ter. 26
· DDE 2.1 control unit K70 defective
|
|
|
If nominal values are attained
|
· Check adjustment of brake lamp switch
S8
· Brake lamp switch S8 defective
|
|
Trouble-shooting for data list parameter 08:
|
|
|
|
· Ignition ON
· Disconnect wiring harness plug from
brake lamp switch S8
· TECH 1 data list no. 08
|
INACTIVE 12V
|
· Short circuit to ground
from: wiring
harness plug for DDE 2.1 control unit K70 Ter. 31
to: wiring
harness plug for brake lamp switch S8 Ter. 4
· DDE 2.1 control unit K70 defective
|
|
· Jumper wiring harness plug for brake
lamp switch S8
from: wiring
harness plug for brake lamp switch S8 Ter. 4
to: ground
· TECH 1 data list no. 08
|
ACTIVE 0V
|
· Short circuit to voltage/ circuit
interruption
from: wiring
harness plug for DDE 2.1 control unit K70 Ter. 31
to: wiring
harness plug for brake lamp switch S8 Ter. 4
· DDE 2.1 control unit K70 defective
|
|
· Jumper wiring harness plug for brake
lamp switch S8
from: wiring
harness plug for brake lamp switch S8 Ter. 4
to: wiring
harness plug for brake lamp switch S8 Ter. 3
· TECH 1 data list no. 08
|
ACTIVE 0V
|
· Circuit interruption
from: wiring
harness plug for brake lamp switch S8 Ter. 3
to: ground
|
|
|
If nominal values are attained
|
· Check adjustment of brake lamp switch
S8
· Brake lamp switch S8 defective
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|