Vauxhall Workshop Service and Repair Manuals

KM-133-C

Remover/Installer

To remove and install the injector nozzles

KM-226-A

Measuring Device

Set start of delivery

KM-235-D

Installer

Install crankshaft needle bearing

KM-263-B

Engine Lifter

To hold/lift the engine

KM-301

Gauge Bar

To measure valve and piston projection

KM-328-B

Remover

Remove shifting lock closure plugs in conjunction with KM-630

KM-340-1-G

Cutter Set

To cut and correct valve seating

KM-348

Spring Compressor

To compress valve springs

KM-412-A

Engine Overhaul Stand

To hold removed engine

KM-412-14

Adapter

Engine mount in conjunction with KM-412-A

KM-469-A

Remover / Installer

Timing case seal ring

KM-470-B

Angular Torque Wrench

To tighten cylinder head bolts

KM-471

Adapter

To check pressurised cooling system in conjunction with cooling system tester

KM-488

Connecting Piece

To check compression.

KM-498-B

Oil Pressure Gauge

Check engine oil pressure together with KM-830

KM-533-B

Connecting Piece

To check pressure loss in conjunction with KM-488

MKM-571-B

Dial Gauge

To measure start of delivery in conjunction with KM-226-A

MKM-596-A

Temperature Gauge

To measure oil temperature

MKM-604-D

Torx Bit and Socket Set

To remove/install Torx bolts

KM-609

Electronic-Kit I

Diagnosis of electric and electronic systems

MKM-610

Torque Wrench 1/2'' drive

Range 30 to 130 Nm / 22 to 96 lbf. ft.

MKM-611

Torque Wrench 3/8'' drive

Range 10 to 60 Nm / 7.5 to 44.5 lbf. ft.

MKM-667-A

Pressure and Vacuum Pump

To measure turbocharger charge pressure

KM-810-A

Test Lamp

To adjust crankshaft pulse pick-up bracket

KM-811

Locking Tool

To hold camshaft in place

KM-812

Line Wrench

To loosen union nuts for injection lines

KM-813

Test Drift

To check crankshaft TDC position

KM-814

Locking Device

To lock flywheel/drive disc

KM-815

Installer

To press seal ring in timing case

KM-816

Installer

To insert guide bearing in conjunction with KM-235-1

KM-817

Installer

To install crankshaft rear seal ring in rear end cover with KM-235-1

KM-818

Installer

To insert rear closure cover with crankshaft seal ring

KM-819

Counterhold

To loosen/tighten torsional damper hub

KM-820

Open-ended Wrench SW 32

To loosen and tighten visco-fan with torque wrench 3/8"

KM-821

Counterhold

To loosen and tighten visco-fan

KM-822

Cam Lever

To release upper timing chain at chain tensioner

KM-823

Remover Pins

To remove dual chain tensioner

KM-824-A

Socket Wrench

To loosen and tighten bearing pins for ribbed V-belt

KM-825

Remover

To remove injection pump

KM-826

Adjustment Lever

Basic adjustment of injection pump

KM-827

Centring Tool

To centre oil pump

KM-828

Guides

To install con-rods in crankshaft

KM-829

Adapter

To check fuel supply pressure with KM-J-34730-91

KM-830

Adapter

To check oil pressure with KM-498-B

KM-831

Reamer Set Ø 6 mm

To ream valve guide

KM-835-A

Installer

To insert valve stem seals

KM-839

Hold-Down Device

To remove and install camshaft

KM-840

Remover

To remove valve stem seals

KM-841

Plastic Protection

Plastic protective foil for removing/installing valves/valve springs

KM-842

Pressing Device

Pressing device for leak check of cylinder head

KM-843

Mounting Device

Installer for operations on cylinder head

KM-844

Adapter

To tension valve springs with KM-348

KM-845

Suction Device

To remove hydraulic valve lifter

KM-849

Support Device

Storage facility for pistons, con-rods and valves

MKM-883-1

Engine Bridge

Hold/Lower the engine together with MKM-883-4-A

MKM-883-4-A

Retaining hook

Hold/Lower the engine together with KM-883-1

KM-904-B

Base Frame

To remove and install various vehicle components with additional adapters

KM-917

Remover

To disconnect coolant lines

KM-6190

Engine / Transmission Holder

To remove/install drive unit

KM-6278

Engine Shackle

To remove and install engine