| |
Nm
|
|
Adapter, fuel distributor pipe to intake bridge
|
8
|
|
Adapter, fuel distributor pipe to fuel distributor pipe
|
15
|
|
Starter to cylinder block
|
40
|
|
Intake bridge to intake flange
|
20
|
|
Intake flange to cylinder head
|
20
|
|
Drive disc / flywheel to crankshaft
|
65 + 30° + 15° 1) 2)
|
|
Exhaust manifold to cylinder head
|
20 3)
|
|
Oil filter housing cover to oil filter housing
|
25
|
|
Heat exchanger cover to heat exchanger
|
30
|
|
Heat exchanger cover to cylinder block
|
20
|
|
DIS ignition module to member
|
8
|
|
Torsional vibration damper to toothed belt drive gear
|
20
|
|
Throttle body to intake plenum
|
8
|
|
Pressure line to power steering pump
|
28
|
|
Accelerator pedal module to bulkhead
|
20
|
|
Link rod to stabiliser
|
65 3)
|
|
Alternator to cylinder block and oil pump
|
35
|
|
Transmission to cylinder block (M8)
|
20
|
|
Transmission to cylinder block (M12)
|
60
|
|
Transmission holder to underbody
|
45 4)
|
|
Threaded sleeves to crankshaft bearing bridge
|
8
|
|
Base plate, toothed belt tension roller and toothed belt guide
roller to cylinder head
|
40
|
|
Auxiliary aggregate(s) support to cylinder block
|
35
|
|
Idler bracket to body
|
55 + 75° + 15° 1)
|
|
Rear toothed belt cover to cylinder head and oil pump (M6)
|
8
|
|
Rear toothed belt cover to cylinder head and oil pump (M8)
|
10
|
|
Crankshaft pulse pick-up in cylinder block
|
8
|
|
Crankshaft pulse pick-up disc to crankshaft
|
15 1)
|
|
Refrigerant lines to compressor
|
40
|
|
Ribbed V-belt pulley to coolant pump
|
8 + 30° + 30° 1)
|
|
Ribbed V-belt pulley to power steering pump
|
20 + 30° + 15° 1)
|
|
Ribbed v-belt tension roller to cylinder head
|
35
|
|
Knock sensor to cylinder block
|
20
|
|
Fuel lines to adapter, fuel distributor pipe
|
15
|
|
Fuel distributor pipe to intake bridge
|
8
|
|
Coolant bridge to cylinder head
|
30 5)
|
|
Coolant intake pipe to exhaust manifold
|
8
|
|
Coolant intake pipe to cylinder block
|
20
|
|
Coolant pump to cylinder block
|
25
|
|
Coolant pipe and engine transport shackle to cylinder head
|
25
|
|
Ball joint to steering knuckle
|
100 3)
|
|
Crankshaft bearing bridge to cylinder block
|
20
|
|
Crankshaft bearing cap and crankshaft bearing bridge to cylinder
block cylinder block
|
50 + 60° + 15° 1)
|
|
Oxygen sensor in front exhaust pipe
|
30
6)
|
|
Steering arm to steering shaft
|
160 3)
|
|
Solenoid valve for intake plenum switchover valve to switchover
valve
|
8
|
|
Secondary air metal pipe to exhaust manifold
|
20
|
|
Engine damping block to engine bracket
|
40
|
|
Engine vent housing to cylinder block
|
8
|
|
Engine damping block to front axle body
|
55
|
|
Engine bracket to cylinder block
|
40
|
|
Engine bracket, engine damping block to cylinder block
|
60
|
|
Camshaft bearing caps to cylinder head
|
8
|
|
Camshaft sprocket to camshaft
|
50 + 60° + 15° 1)
|
|
Camshaft sensor to camshaft bearing cap
|
8
|
|
Oil drain bolt to oil pan (inner Torx bolt)
|
10
|
|
Oil drain bolt to oil pan (hex bolt)
|
55
|
|
Oil pressure switch to oil pump
|
40
|
|
Oil filter to cylinder block
|
15
|
|
Oil filter casing to cylinder block
|
45
|
|
Oil lines (banjo bolt) to heat exchanger
|
30 + 30° + 15° 1)
|
|
Oil lines to cylinder block
|
30
|
|
Oil pump to cylinder block (up to MY '99) – M6 bolt
|
8 + 10
7)
8)
|
|
Oil pump to cylinder block (as of MY '99) – M8 bolt
|
12 + 20
8)
9)
|
|
Oil intake pipe to oil pump and to crankshaft bearing bridge
|
8
|
|
Oil baffle plate to crankshaft bearing bridge
|
8
|
|
Oil feed and return lines to cylinder block
|
30
|
|
Upper part of oil pan to transmission housing – M8
bolt
|
20
|
|
Upper part of oil pan to transmission housing – M10
bolt
|
40
|
|
Upper part of oil pan housing to cylinder block and oil pump
|
15
|
|
Lower part of oil pan housing to upper part of oil pan
housing
|
8 + 30° 1)
|
|
Con-rod bearing cap to con-rod
|
35 + 45° + 15° 1)
|
|
Wheel to wheel hub
|
110
|
|
Intake plenum to intake bridge
|
8
|
|
Shift outrigger to transmission
|
20
|
|
Hose clamps for air intake hose
|
3.5
|
|
Clamp, fuel pressure regulator to fuel distributor pipe
|
5
|
|
Vibration damper to front axle body bracket and to engine
bracket
|
40
|
|
Coolant temperature sensor in coolant bridge
|
18
|
|
Tie rod to steering knuckle
|
60 3)
|
|
Support to exhaust gas recirculation valve adapter
|
20
|
|
Tank vent valve to engine vent housing
|
8
|
|
Temperature sensor to coolant bridge
|
18
|
|
Thermostat housing to cylinder block
|
20
|
|
Union nut to screw-on connection, exhaust gas recirculation
valve adapter
|
25
10)
|
|
Intake plenum switchover valve to intake plenum
|
8
|
|
Brake servo vacuum line to intake plenum
|
20
|
|
AC compressor to auxiliary aggregates support
|
35
|
|
Oil pressure regulating valve screw plug to oil pump
|
60
|
|
Closure bolt, safety valve to oil pump
|
30
|
|
Front axle body to body (front)
|
65 + 30° + 15° 1)
|
|
Front axle body to side member (centre)
|
150 + 30° + 15° 1)
|
|
Front axle body to side member (rear)
|
130 + 30° + 15° 1)
|
|
Front toothed belt cover to rear toothed belt cover
|
8
|
|
Front exhaust pipe to exhaust manifold
|
30
|
|
Pre-volume chamber to fastening points
|
2.5
|
|
Exhaust gas recirculation corrugated pipe to exhaust gas
recirculation valve adapter and exhaust manifold
|
25
|
|
Toothed belt tension roller to bracket
|
20
|
|
Toothed belt guide roller to cylinder block
|
40
|
|
Toothed belt guide roller to toothed belt tension roller
bracket
|
40
|
|
Toothed belt guide roller to oil pump
|
40
|
|
Toothed belt drive gear to crankshaft
|
250 + 45° + 15° 1)
|
|
Spark plugs to cylinder head
|
25
|
|
Cylinder head to cylinder block
|
25 + 270° + 15° 1) 11) 12)
|
