|
Special tools - DOHC II
|
KM-135
|
Adapter
|
|
To measure engine oil pressure in conjunction with KM-498-B
|
|
KM-194-E
|
Spark Plug Key
|
|
To remove/install spark plug
|
|
KM-235-D
|
Installer
|
|
To install crankshaft needle bearing and seal ring
|
|
KM-236-B
|
Remover
|
|
To remove joints from steering arm and idler arm
|
|
KM-263-B
|
Engine Lifter
|
|
To hold/lift the engine
|
|
KM-301
|
Gauge Bar
|
|
To check piston projection
|
|
|
|
KM-328-B
|
Remover
|
|
To drive out crankshaft needle bearing
|
|
KM-412
|
Engine Overhaul Stand
|
|
To hold removed engine
|
|
KM-412-8-A
|
Adapter
|
|
To hold engine in conjunction with KM-412
|
|
KM-422
|
Installer
|
|
To install seal ring into camshaft carrier
|
|
|
|
KM-427
|
Remover/Installer
|
|
To install guide pins into engine block
|
|
KM-469-A
|
Remover / Installer
|
|
To remove and install crankshaft seal ring
|
|
KM-470-B
|
Angular Torque Wrench
|
|
To tighten cylinder head bolts
|
|
KM-471
|
Adapter
|
|
To check pressurised cooling system in conjunction with cooling
system tester
|
|
KM-498-B
|
Oil Pressure Gauge
|
|
To check engine oil pressure in conjunction with KM-135
|
|
KM-535
|
Installer
|
|
To install crankshaft seal ring in conjunction with KM-635
|
|
|
|
MKM-571-B
|
Dial Gauge
|
|
To measure piston projection
|
|
MKM-596-A
|
Temperature Gauge
|
|
To measure oil temperature, exhaust gas test
|
|
MKM-604-D
|
Torx Bit and Socket Set
|
|
To remove/install Torx bolts
|
|
KM-609
|
Electronic Kit I
|
|
Diagnosis of electric and electronic systems
|
|
MKM-610
|
Torque Wrench, 1/2"
|
|
Range 30 – 130 Nm / 22 – 96 lbf. ft.
|
|
MKM-611
|
Torque Wrench, 3/8"
|
|
Range 10 – 60 Nm / 7 – 44 lbf. ft.
|
|
|
|
KM-635
|
Installer
|
|
To install rear crankshaft seal ring in conjunction with
KM-535
|
|
KM-652
|
Flywheel Holder
|
|
To lock flywheel or drive disc
|
|
KM-653-A
|
Adapter
|
|
To tension valve spring in conjunction with KM-348
|
|
KM-662-C
|
Holding Wrench
|
|
To keep the toothed belt drive gear fixed when removing or
installing the fastening bolt
|
|
MKM-667
|
Pressure and Vacuum Pump
|
|
To check vacuum units for leaks
|
|
MKM-669
|
Torque Wrench, 1/2"
|
|
Range 50 – 300 Nm / 37 – 221 lbf. ft.
|
|
|
|
KM-693-A
|
Assembly Sleeves
|
|
To install front crankshaft seal ring
|
|
KM-726-A
|
Oil Filter Wrench
|
|
To remove/install the oil filter
|
|
KM-798
|
Dial Gauge
|
|
To measure tooth backlash of balancer shaft unit
|
|
KM-835-A
|
Installer
|
|
To install valve stem sealing
|
|
MKM-836
|
Remover
|
|
To remove spark plug connector
|
|
|
|
KM-840
|
Remover
|
|
To remove valve stem seal
|
|
KM-845
|
Suction Device
|
|
To remove the hydraulic valve lifters
|
|
KM-853
|
Locking Tool
|
|
To lock the camshaft sprockets
|
|
MKM-874
|
Precision Multimeter
|
|
To test electrical/electronic components
|
|
MKM-883-1
|
Engine Bridge
|
|
Hold/lift engine in combination with KM-883-4-A
|
|
MKM-883-4-A
|
Securing hook
|
|
Hold/lift engine in combination with KM-883-1
|
|
|
|
KM-913-A
|
Installation Wrench
|
|
To tension/relax the ribbed V-belt tension roller
|
|
KM-949
|
Measurement Sensor
|
|
To measure in conjunction with KM-798
|
|
KM-2355
|
Socket Wrench T55
|
|
To loosen/tighten cylinder head bolts
|
|
KM-2358
|
Engine Lifter Shackles
|
|
To remove and install engine
|
|
KM-6009
|
Remover/Installer
|
|
To remove/install ignition module
|
|
KM-6086
|
Automatic Valve Spring Lever
|
|
Removal/installation or valve springs and valve keepers
|
|
|
|
KM-6190
|
Engine / Transmission Holder
|
|
To remove/install drive unit
|
|
KM-J-26792
|
Checking Spark Plug
|
|
To check ignition spark
|
|
KM-J-34730-91
|
Pressure Tester
|
|
To check fuel pressure
|
|
KM-J-37228
|
Separation Tool
|
|
To remove one-piece oil pan
|
|
|
|
