|
Nm
|
Starter to transmission (long bolt)
|
60
|
Starter to cylinder block
|
45
|
Drive disc to crankshaft
|
55 + 30° + 15° 1)
|
Exhaust manifold to cylinder head
|
22 2)
|
Steering arm fastening nut
|
160
|
Fastening bolt for front axle body, front, to front member
|
65 + 30° + 15° 1)
|
Fastening bolt for centre front axle body to side member
|
150 + 30° + 15° 1)
|
Fastening bolt for front axle body, rear, to side member
|
130 + 30° + 15° 1)
|
Fastening clamp to fuel pressure regulator
|
5
|
Pressure plate cover to camshaft housing
|
8
|
DIS ignition module to bracket
|
8
|
Torsional vibration damper to toothed belt drive gear
|
20
|
Throttle body to intake manifold
|
9
|
Pressure plate to camshaft housing
|
8
|
Intake manifold to cylinder head
|
22
|
Crankcase ventilation flange to cylinder block
|
25
|
Guide joints to steering knuckle
|
100 1)
|
Crankshaft pulse pick-up sensor disc to crankshaft
|
13 2)
|
Propshaft to transmission
|
95
|
Auxiliary aggregate(s) support to cylinder block
|
35
|
Bracket to exhaust pipe bracket
|
20
|
Bowden cable bracket to intake manifold
|
8
|
DIS ignition module bracket to camshaft housing
|
15
|
DIS ignition module bracket to cylinder head
|
15
|
Alternator bracket to cylinder block
|
35
|
Wiring harness bracket to camshaft housing
|
15
|
Idler bracket to body
|
55 + 75° + 15° 1)
|
Oil intake pipe bracket to cylinder block
|
6
|
Compressor bracket to cylinder block and auxiliary aggregates
support
|
35
|
Rear fastening bolts to compressor bracket
|
18
|
Rear toothed belt cover to oil pump and camshaft housing
|
6
|
Heat shield sleeves in cylinder head
|
25 3)
|
High-pressure line to power steering pump
|
28
|
Crankshaft pulse pick-up to cylinder block
|
8
|
Wiring trough to camshaft housing
|
8
|
Wiring trough to front toothed belt cover
|
4
|
Ribbed V-belt tension roller to ancillary component support
|
25
|
Knock sensor to cylinder block
|
20
|
Fuel line(s) to fuel distributor pipe
|
22.5
|
Fuel distributor tube to intake manifold
|
8
|
Coolant outlet port to thermostat housing
|
8
|
Coolant pump to cylinder block
|
25
|
Crankshaft bearing cap to cylinder block
|
50 + 45° + 15° 1)
|
Oxygen sensor in front exhaust pipe
|
30
4)
|
Shackle to intake manifold and alternator
|
18
|
Power steering pump shackle to support
|
20
|
Air intake hose to throttle body
|
3.5
|
Air intake hose to air cleaner housing
|
3.5
|
Ground cable to fuel distributor pipe
|
4.4
|
Ground cable to camshaft housing
|
20
|
Ground cable to cylinder block
|
20
|
Engine damping block to engine bracket
|
40
|
Engine damping block to front axle body
|
55
|
Engine bracket to cylinder block
|
60
|
Engine support to transmission and cylinder block
|
40
|
Engine transport shackle to camshaft housing
|
15
|
Camshaft housing cover to camshaft housing
|
8
|
Camshaft sprocket to camshaft
|
45
|
Oil drain bolt to oil pan
|
55
|
Oil pressure switch to oil pump
|
40
|
Oil filter to oil pump
|
15
|
Fluid cooler lines to radiator
|
30
|
Oil pump to cylinder block
|
8
|
Oil pump cover to oil pump
|
6
|
Oil intake pipe to oil pump
|
8
5) 6)
|
Oil pan to oil pump and cylinder block
|
8
5) 6)
|
Con-rod bearing cap to con-rod
|
35 + 45° + 15° 1)
|
Power steering pump to ancillary component support
|
25
|
Wheel to wheel hub
|
110
|
Clamp, fuel pressure regulator to fuel distributor pipe
|
5
|
Hose clamps for air intake hose
|
3.5
|
Flywheel to crankshaft
|
65 + 30° + 15° 1) 7)
|
Coolant temperature sensor to thermostat housing
|
11
|
Starter support to cylinder block
|
25
|
Tie rod to steering knuckle
|
60
|
Support to intake manifold and alternator
|
20
|
Tank vent valve to camshaft housing
|
10
|
Coolant temperature sensor to thermostat housing
|
10
|
Thermostat housing to cylinder head
|
15
|
Brake servo vacuum line to inlet manifold
|
20
|
Lower alternator fastening bolt to alternator bracket
|
35
|
Lower engine compartment cover to front axle body
|
5
|
Closure bolt, safety valve to oil pump
|
50
|
Front fastening bolts for compressor to auxiliary aggregates
support
|
35
|
Front toothed belt cover to rear toothed belt cover
|
4
|
Front exhaust pipe to exhaust manifold
|
25 3)
|
Toothed belt tension roller to oil pump
|
20
|
Toothed belt drive gear to crankshaft
|
130 + 45° ± 5° 1)
|
Spark plug to cylinder head
|
20
|
Cylinder head and camshaft housing to cylinder block
|
25 + 90° + 90° + 90° 1) 8)
|