Special Service Tools (X 18 XE, X 20 XEV, C 20 SEL, C 22 SEL)
|
KM-135 |
Adapter |
|
To measure engine oil pressure in conjunction with KM-498-B |
|
KM-194-E |
Spark Plug Wrench |
|
To remove/install spark plug |
|
KM-301 |
Gauge Bar |
|
To check piston projection |
|
KM-340-F |
Cutter Set |
|
To cut and correct valve seating |
|
KM-348 |
Valve Spring Compressor |
|
To compress valve spring in conjunction with KM-653-A |
|
KM-412 |
Engine Overhaul Stand |
|
To hold removed engine |
| 
|
|
KM-412-8-A |
Adapter |
|
To hold engine in conjunction with KM-412 |
|
KM-422 |
Installer |
|
To press seal ring in camshaft |
|
KM-470-B |
Angular Torque Wrench |
|
To tighten cylinder head bolts |
|
KM-471 |
Adapter |
|
To check pressurised cooling system in conjunction with coolant tester |
|
KM-498-B |
Oil Pressure Gauge |
|
To check engine oil pressure in conjunction with KM-135 |
|
KM-535 |
Installer |
|
To install crankshaft seal ring in conjunction with KM-635 |
| 
|
|
MKM-571-B |
Dial Gauge |
|
To check various components |
|
MKM-596-A |
Temperature Gauge |
|
To measure oil temperature |
|
MKM-604-D |
Torx Bit and Socket Set |
|
To remove/install Torx bolts |
|
KM-609 |
Electronic-Kit I |
|
To diagnose electrical and electronic systems |
|
MKM-610 |
Torque Wrench, 1/2" |
|
Measuring range 30 - 130 Nm / 22 - 96 lbf. ft. |
|
MKM-611 |
Torque Wrench, 3/8" |
|
Measuring range 10 - 60 Nm / 7 - 44 lbf. ft. |
| 
|
|
KM-635 |
Installer |
|
To install rear crankshaft seal ring in conjunction with KM-535 |
|
KM-652 |
Flywheel / Drive Disc Holder |
|
To lock flywheel or drive disc |
|
KM-653-A |
Adapter |
|
To tension valve spring in conjunction with KM-348 |
|
KM-662-C |
Holding Wrench |
|
To hold toothed belt drive gear when removing and installing fastening bolt |
|
MKM-667 |
Pressure and Vacuum Pump |
|
To check vacuum units for leaks |
|
KM-693-A |
Installer |
|
To install front crankshaft seal ring |
| 
|
|
KM-726-A |
Oil Filter Wrench |
|
To remove/install the oil filter |
|
KM-796 |
Dismantler |
|
To open quick-release fittings for fuel system |
|
KM-798 |
Dial Gauge |
|
Measure backlash |
|
KM-805 |
Reamer 6 mm |
|
To ream the valve guide, oversize 0.075 mm |
|
KM-835-A |
Installer (6 mm) |
|
To install the valve stem seal |
|
KM-836 |
Remover |
|
To remove spark plug connector |
| 
|
|
KM-840 |
Remover |
|
To remove valve stem seals |
|
KM-845 |
Suction Device |
|
To remove the hydraulic valve lifters |
|
KM-853 |
Locking Tool |
|
To lock the camshaft sprockets |
|
MKM-883-1 |
Engine Bridge |
|
To hold/lift the engine |
|
MKM-883-2 |
Adapter Plate |
|
To align engine in conjunction with MKM-883-1 |
|
MKM-889 |
Remover/Installer |
|
To remove/install the valve stem seals (cylinder head installed) |
| 
|
|
KM-897 |
Third Engine Transportation Shackle |
|
To remove and install engine |
|
KM-904 |
Base Frame |
|
To remove and install various vehicle components with additional adapters |
|
KM-905 |
Centring Locator |
|
To remove/install the front axle body in conjunction with KM-904 |
|
KM-913-A |
Installation Wrench |
|
To tension/relax the ribbed V-belt tension roller |
|
KM-949 |
Measuring Gauge |
|
Measure backlash |
|
KM-2355 |
Socket Wrench |
|
To loosen/tighten cylinder head bolts |
| 
|
|
KM-J-34730-91 |
Pressure Tester |
|
To check fuel pressure |
| 
|
|
