Special Tools (X 20 DTL, X 20 DTH)
|
KM-135
|
Adapter
|
To measure engine oil pressure in conjunction with KM-498-B
|
|
KM-301
|
Measurement Bridge
|
To check piston projection
|
|
KM-328-B
|
Puller
|
To pull injection nozzles out of cylinder head, in conjunction
with KM-931
|
|
KM-348
|
Valve Spring Compressor
|
To squeeze together valve springs in conjunction with
KM-653-A.
|
|
KM-412
|
Engine Assembly Stand
|
To support the engine when removed
|
|
KM-412-8-1
|
Adapter
|
Engine support in conjunction with KM-412
|
|
|
|
KM-412-16
|
Adapter
|
Engine support in conjunction with KM-412
|
|
KM-427
|
Remover and Installer
|
To drive the centring pins into the cylinder block
|
|
KM-454-4
|
Installer
|
To install crankshaft seal ring in conjunction with KM-934
|
|
KM-470-B
|
Angular Torque Wrench
|
To tighten cylinder head bolts
|
|
KM-471
|
Adapter
|
To check cooling system under pressure in conjunction with
coolant test device
|
|
KM-498-B
|
Oil Pressure Gauge
|
To check engine oil pressure in conjunction with KM-135
|
|
|
|
KM-533-1
|
Adapter
|
To check for pressure loss in conjunction with KM-928
|
|
KM-533-2
|
Adapter
|
To check compression pressure in conjunction with KM-928
|
|
KM-535
|
Installer
|
To install crankshaft rear seal ring in conjunction with
KM-934
|
|
MKM-571-B
|
Dial Gauge
|
To check various components
|
|
MKM-596-A
|
Temperature Measuring Device
|
To measure the oil temperature
|
|
MKM-604-D
|
Torx Bit and Socket Set
|
To remove and install Torx bolts
|
|
|
|
MKM-604-30
|
Torx Socket
|
To remove and install the injection pump
|
|
KM-609
|
Electronics Kit I
|
To diagnose electronic and electrical systems
|
|
MKM-610
|
1/2" Torque Wrench
|
Measuring range 30 - 130 Nm
|
|
MKM-611
|
3/8" Torque Wrench
|
Measuring range 10-60 Nm
|
|
KM-652
|
Flywheel/Drive Disc Holder
|
To lock the flywheel or drive disc
|
|
KM-653-A
|
Adapter
|
To tension the valve springs in conjunction with KM-348
|
|
|
|
MKM-667-A
|
Pressure and Vacuum Pump
|
To check vacuum diaphragms for leaks, to check traverse gasket
for leaks in conjunction with MKM-667-10
|
|
KM-717
|
Pulling Pliers
|
To remove wiring harness connector for glow plugs
|
|
KM-796-A
|
Remover
|
To open quick fittings on fuel system
|
|
KM-805
|
Reamer (6 mm)
|
To ream the valve guide, oversize 0.075
|
|
KM-835-A
|
Installer
|
To install the valve stem seals (6 mm)
|
|
KM-840
|
Remover
|
To remove the valve stem seals
|
|
|
|
KM-845
|
Suction Tool
|
To remove the hydraulic valve lifters
|
|
MKM-883-1
|
Engine Bridge
|
To hold/lift the engine
|
|
MKM-883-2
|
Adapter Plate
|
To align the engine in conjunction with MKM-883-1
|
|
MKM-889
|
Remover and Installer
|
To remove and install the valve stem seals (cylinder head
installed)
|
|
KM-904
|
Base Frame
|
To remove and install various vehicle components in conjunction
with additional adapters
|
|
KM-905
|
Centring Support
|
To remove and install the front axle body in conjunction with
KM-904
|
|
|
|
KM-917
|
Remover
|
To disconnect the refrigerant lines (quick fittings)
|
|
MKM-923
|
Wiring Harness Repair Kit
|
To repair cables for all vehicles
|
|
KM-926
|
Wrench
|
To remove and install hydraulic engine mounts
|
|
KM-927
|
Fixing Pins
|
To lock distributor injection pump in TDC position
|
|
KM-928
|
Adapter
|
To check compression pressure in conjunction with KM-533-2
|
|
KM-929
|
Fixing Pins
|
To lock the crankshaft in cyl. 1 TDC position
|
|
|
|
KM-930
|
Holding Wrench
|
To hold the torsional vibration damper when removing and
installing the fastening bolt
|
|
KM-931
|
Remover
|
To remove the injection nozzle
|
|
KM-932
|
Locking Tool
|
To lock the camshaft in cyl. 1 TDC position
|
|
KM-933
|
Adjuster
|
To adjust the valve timing
|
|
KM-934
|
Installer
|
To install the crankshaft rear seal ring in conjunction with
KM-535
|
|
KM-935
|
Installer
|
To install the crankshaft front seal ring
|
|
|
|
KM-946
|
Protective Caps
|
To remove and install valve springs/valve collets
|
|
KM-948
|
Bleed Device
|
To bleed the fuel system
|
|
KM-977-1
|
Holding Wrench
|
To remove and install the crankshaft pulley, with handle
KM-956-1
|
|
KM-980
|
Removing/Installing Wrench
|
To remove and install the glow plug
|
|
KM-6042
|
Remover
|
Shift cables to transmission (F 23 manual transmission only)
|
|
KM-6173
|
Engine Mount
|
To hold engine on front axle body
|
|
|
|
KM-6318
|
Installer
|
To install seal ring between injection nozzle and injection
nozzle traverse
|
|
|
|