Trouble Code Table, X 25 XE
Trouble code |
Information sensor |
Cause of fault |
new |
old |
|
|
P 0100 |
74 |
Hot film mass air flow meter |
Voltage high |
|
72 |
Hot film mass air flow meter |
Voltage low |
P 0110 |
71 |
Intake air temperature sensor |
Voltage high |
|
69 |
Intake air temperature sensor |
Voltage low |
P 0115 |
15 |
Coolant temperature sensor |
Voltage high |
|
14 |
Coolant temperature sensor |
Voltage low |
P 0120 |
21 |
Throttle valve potentiometer |
Voltage high |
|
22 |
Throttle valve potentiometer |
Voltage low |
P 0130 |
39 |
Oxygen sensor - circuit 1 |
Voltage high |
|
38 |
Oxygen sensor - circuit 1 |
Voltage low |
|
13 |
Oxygen sensor - circuit 1 |
Cable interruption |
P 0150 |
91 |
Oxygen sensor - circuit 2 |
Voltage high |
|
89 |
Oxygen sensor - circuit 2 |
Voltage low |
|
98 |
Oxygen sensor - circuit 2 |
Cable interruption |
P 0170 |
45 |
Oxygen sensor - circuit 1 |
Mixture rich |
|
44 |
Oxygen sensor - circuit 1 |
Mixture lean |
P 0173 |
122 |
Oxygen sensor - circuit 2 |
Mixture rich |
|
121 |
Oxygen sensor - circuit 2 |
Mixture lean |
Explanation of new trouble codes - see section 16.2.2 Notice: The terms "information sensor" and "cause of fault" in the trouble code table merely give an indication on the cause of the fault; i.e. when a trouble code is indicated, the component specified in the trouble code table is not necessarily at fault. The connection leads, plug connections and voltage supply must also be considered as alternative causes of the fault.
2.6.8 Trouble Code Table, X 25 XE (continued)
Trouble code |
Information sensor |
Cause of fault |
new |
old |
|
|
P 0201 |
25 |
Injector 1 |
Voltage high |
|
81 |
Injector 1 |
Voltage low |
P 0202 |
26 |
Injector 2 |
Voltage high |
|
82 |
Injector 2 |
Voltage low |
P 0203 |
27 |
Injector 3 |
Voltage high |
|
83 |
Injector 3 |
Voltage low |
P 0204 |
28 |
Injector 4 |
Voltage high |
|
84 |
Injector 4 |
Voltage low |
P 0205 |
29 |
Injector 5 |
Voltage high |
|
85 |
Injector 5 |
Voltage low |
P 0206 |
32 |
Injector 6 |
Voltage high |
|
86 |
Injector 6 |
Voltage low |
P 0230 |
54 |
Fuel pump relay |
Voltage high |
|
53 |
Fuel pump relay |
Voltage low |
P 0325 |
16 |
Knock sensor 1 |
No signal/short circuit |
P 0330 |
17 |
Knock sensor 2 |
No signal/short circuit |
P 0335 |
31 |
Crankshaft pulse pick-up |
No engine speed signal |
|
19 |
Crankshaft pulse pick-up |
Incorrect engine speed signal |
P0340 |
94 |
Camshaft sensor |
Voltage high |
|
93 |
Camshaft sensor |
Voltage low |
P0403 |
34 |
Exhaust gas recirculation valve |
Voltage high |
|
33 |
Exhaust gas recirculation valve |
Voltage low |
P 0410 |
47 |
Secondary air pump relay |
Voltage high |
|
46 |
Secondary air pump relay |
Voltage low |
Explanation of new trouble codes - see section 16.2.2
2.6.8 Trouble Code Table, X 25 XE (continued)
Trouble code |
Information sensor |
Cause of fault |
new |
old |
|
|
P 0443 |
62 |
Tank vent valve |
Voltage high |
|
61 |
Tank vent valve |
Voltage low |
P 0505 |
57 |
Idle air adjuster |
Voltage low |
|
56 |
Idle air adjuster |
Voltage high |
P 0560 |
49 |
Battery |
Voltage high |
|
48 |
Battery |
Voltage low |
P 0602 |
- |
Control unit programming error |
General error |
P 1110 |
63 |
Switchover valve solenoid valve 1 |
Voltage high |
|
59 |
Switchover valve solenoid valve 1 |
Voltage low |
P 1111 |
134 |
Switchover valve solenoid valve 2 |
Voltage high |
|
133 |
Switchover valve solenoid valve 2 |
Voltage low |
P 1112 |
123 |
Switchover valve 1 |
Blocked |
P 1113 |
124 |
Switchover valve 2 |
Blocked |
Explanation of new trouble codes - see section 16.2.2. Notice: The terms "information sensor" and "cause of fault" in the trouble code table merely give an indication on the cause of the fault; i.e. when a trouble code is indicated, the component specified in the trouble code table is not necessarily at fault. The connection leads, plug connections and voltage supply must also be considered as alternative causes of the fault.
2.6.8 Trouble Code Table, X 25 XE (continued)
Trouble code |
Information sensor |
Cause of fault |
new |
old |
|
|
P 1405 |
132 |
Exhaust gas recirculation potentiometer |
Implausible signal |
P 1501 |
59 |
Immobiliser control unit |
Immobiliser initialised incorrectly or not at all |
P 1502 |
93 |
Immobiliser control unit |
No frequency code |
P 1503 |
94 |
Immobiliser control unit |
Incorrect frequency code |
P 1530 |
88 |
Compressor cutoff relay |
Voltage high |
|
87 |
Compressor cutoff relay |
Voltage low |
P 1600 |
55 |
Control unit |
Defective |
P 1601 |
137 |
Temperature sensor control unit |
Temperature too high |
P 1602 |
18 |
Knock control module |
Defective |
P 1640 |
136 |
Control unit |
Defective |
P 1690 |
52 |
Engine telltale |
Voltage high |
|
135 |
Engine telltale |
Voltage low |
P 1740 |
75 |
Torque control |
Voltage low |
|
76 |
Torque control |
Voltage high |
Explanation of new trouble codes - see section 16.2.2.
|