Self diagnosis
Display group overview
|
---|
Display group 00 (decimal figures displayed)
|
Display zones
|
|
1
|
2
|
3
|
4
|
5
|
6
|
7
|
8
|
9
|
10
|
Display
|
Coolant temperature
|
Engine load signal
|
Engine speed
|
Lambda factor
|
Learned idling adaption value
|
Learned full load adaption value
|
Learned part load adaption value
|
Learned air mass meter value
|
Not relevant
|
Ignition timing
|
Specification1)
|
182...224
|
26...44
|
80...88
|
92...164
|
-
|
-
|
-
|
-
|
-
|
93...76
|
Corresponds to
|
80...
110 °C
|
1...
60 %
|
800...
880 rpm
|
0.7...1.3
|
-
|
-
|
-
|
-
|
-
|
0...15 <°
|
1)
Specifications are valid for control unit in basic setting
|
---|
|
Display zones
|
|
1
|
2
|
3
|
4
|
Display group 01
|
Display
|
xxxx rpm
|
xxx °C
|
x.x
|
x.x <°
|
Indicated
|
Engine speed
|
Coolant temperature
|
Lambda factor
|
Ignition timing
|
Specification1)
|
800...880
|
80...110
|
0.7...1.3
|
0...15
|
Display group 02
|
Display
|
xxxx rpm
|
xx.xx ms
|
xx.xx V
|
xxx °C
|
Indicated
|
Engine speed
|
Injection period
|
Battery voltage
|
not relevant
|
Specification1)
|
800...880
|
2.4...5.2
|
11.5...15
|
-
|
Display group 03
|
Display
|
xxxx rpm
|
xxx %
|
xx.xx <°
|
xx °C
|
Indicated
|
Engine speed
|
Engine load signal
|
Throttle valve angle
|
Intake manifold temperature
|
Specification1)
|
800...880
|
1...60
|
5...19
|
10...50
|
1)
Specifications are valid for control unit in basic setting
|
---|
|
Display zones
|
|
1
|
2
|
3
|
4
|
Display group 04
|
Display
|
xxxx rpm
|
xxx %
|
xxx
|
xxxxx
|
Indicated
|
Engine speed
|
Engine load signal
|
Road speed signal
|
Operating condition2)
|
Specification1)
|
800...880
|
1...60
|
-
|
-
|
Display group 05
|
Display
|
xxxx rpm
|
xxx
|
xx %
|
xxxxx
|
Indicated
|
Engine speed
|
Learned idling stabilization value
|
Idling stabilization valve duty cycle
|
Adjustment requirements2)
|
Specification1)
|
800...880
|
-
|
30...65
|
-
|
Display group 06
|
Display
|
x.x
|
x.x
|
x.x
|
x.x
|
Indicated
|
Lambda factor
|
Learned idling adaption value3)
|
Learned part load adaption value3)
|
Learned full load adaption value3)
|
Specification1)
|
0.7...1.3
|
-
|
-
|
-
|
1)
Specifications are valid for control unit in basic setting
2)
Significance of figures in 5 digit number block
.
3)
Specification range not yet determined, will be published in a Technical Bulletin.
Relevance of figures in 5 digit number block
|
---|
Relevance when displayed digit = 1
|
x
|
x
|
x
|
x
|
x
|
Adjustment condition (display group 05)
|
Operating condition (display group 04)
|
|
|
|
|
1
|
not relevant
|
Overrun
|
|
|
|
1
|
|
Signal from autom. gearbox
|
Idling
|
|
|
1
|
|
|
not relevant
|
Part load
|
|
1
|
|
|
|
Conditioner standby
|
Full load
|
1
|
|
|
|
|
Conditioner compressor switched on
|
Acceleration
|
-
‒ Additional measures see Repair procedures:
Notes:
-
◆ Press ⇒ button to end read measuring value block.
-
◆ After terminating read measuring value block input 06 for "End output" function and confirm with Q.
|