Golf Mk5
| Assembly overview - output shaft |
Note| t | The output shaft is dismantled as follows: position separating device under 2nd gear synchromeshed gear → Item and press off as described in → Fig.. Remove retaining ring → Item. Then press off locking collar with synchro-hub for 1st and 2nd gear as described in → Fig.. |
| t | When installing new gears or new output shaft, refer to → Electronic parts catalogue „ETKA“ and technical data. |
| t | Always renew both tapered roller bearings together as a set. |
| 1 - | Hexagon nut → Item |
| 2 - | Clutch housing |
| 3 - | Shim |
| q | For output shaft |
| q | Adjustment overview → Chapter |
| 4 - | Small tapered roller bearing outer race |
| q | Removing → Fig. |
| q | Pressing in → Fig. |
| 5 - | Small tapered roller bearing inner race |
| q | Pulling off → Fig. |
| q | Pressing on → Fig. |
| 6 - | Output shaft |
| q | Adjusting → Chapter |
| 7 - | Large tapered roller bearing inner race |
| q | Pulling off → Fig. |
| q | Pressing on → Fig. |
| 8 - | Seal |
| q | Place sealing rings (Qty. 4) on bearing support bolts |
| 9 - | Bearing support |
| q | With large tapered roller bearing outer race and bolts |
| q | Change outer race only together with large tapered roller bearing and bearing support |
| 10 - | Thrust washer |
| q | Shoulder of thrust washer faces tapered roller bearing |
| 11 - | Synchromeshed gear for 1st gear |
| 12 - | Needle bearing |
| q | For 1st gear |
| 13 - | Synchro-ring |
| q | (Inner ring for 1st gear) |
| q | Installation position → Fig. |
| q | Check for wear → Fig. |
| q | Check lugs for scoring |
| 14 - | Outer ring for 1st gear |
| q | Installation position → Fig. |
| q | Check for wear → Fig. |
| q | Renew if scored |
| 15 - | Synchro-ring for 1st gear |
| q | Installation position → Fig. |
| q | Check for wear → Fig. |
| 16 - | Locking collar with synchro-hub for 1st and 2nd gears |
| q | After removing retaining ring → Item, pull off together with bearing support → Fig. |
| q | Dismantling → Fig. |
| q | Assembling locking collar and synchro-hub → Fig., → Fig. and → Fig. |
| q | Installation position → Fig. |
| q | Pressing on → Fig. |
| 17 - | Retaining ring |
| 18 - | Synchro-ring for 2nd gear |
| q | Check for wear → Fig. |
| q | Assemble so that notches engage in locking pieces of locking collar → Item |
| 19 - | Outer ring for 2nd gear |
| q | Insert in synchro-ring → Item. |
| q | Installation position → Fig. |
| q | Renew if scored |
| 20 - | Synchro-ring |
| q | (Inner ring for 2nd gear) |
| q | Check for wear → Fig. |
| q | Check lugs for scoring |
| q | Installation position → Fig. |
| 21 - | Synchromeshed gear for 2nd gear |
| q | Installation position → Fig. |
| 22 - | Needle bearing |
| q | For 2nd gear |
| 23 - | Thrust washer |
| 24 - | Sleeve for 3rd gear needle bearing |
| q | Pressing off with synchromeshed gear for 2nd gear → Fig. |
| q | Pressing on → Fig. |
| 25 - | Needle bearing |
| q | For 3rd gear |
| 26 - | Synchromeshed gear for 3rd gear |
| 27 - | Synchro-ring for 3rd gear |
| q | Check for wear → Fig. |
| 28 - | Locking collar with synchro-hub for 3rd and 4th gears |
| q | Press off with 2nd gear synchromeshed gear → Item and 3rd gear → Item → Fig.. |
| q | Dismantling → Fig. |
| q | Assembling locking collar and synchro-hub → Fig., → Fig. and → Fig. |
| q | Installation position, locking collar and synchro-hub → Fig. |
| q | Pressing on → Fig. |
| 29 - | Sleeve |
| q | For needle bearing |
| q | Press off with 3rd and 4th gear → Item locking collar and synchro-hub → Fig.. |
| q | Pressing on → Fig. |
| 30 - | Needle bearing |
| q | For 4th gear |
| 31 - | Synchro-ring for 4th gear |
| q | Check for wear → Fig. |
| 32 - | Synchromeshed gear for 4th gear |
| 33 - | Thrust washer |
| 34 - | Needle bearing |
| q | For output shaft |
| q | Removing and installing → Fig. |
| 35 - | Gearbox housing |
| 36 - | Sleeve |
| q | For output shaft needle bearing |
| q | Pressing off → Fig. |
| q | Pressing on → Fig. |
| 37 - | Gear wheel for 5th gear |
| q | Pull off individually → Chapter |
| q | Pull off together with gearbox housing → Chapter |
| 38 - | Sleeve |
| 39 - | Gear wheel for 6th gear |
| q | Pull off individually → Chapter |
| q | Pull off together with gearbox housing → Chapter |
| 40 - | Cylindrical roller bearing inner race |
| q | For output shaft |
| q | Larger outer diameter from gearbox date 21 08 6 |
| q | Allocation → Fig. |
| q | Mark before removing |
| q | Do not interchange with inner race for cylindrical roller bearing of input shaft |
| 41 - | Bolt → Item |
| q | Allocation → Fig. |
| q | Self-locking |
| q | Always renew |
