Golf Mk6
| Assembly overview: transverse link, track rod (four-wheel drive) |
| -Arrow- indicates direction of travel. |
| 1 - | Eccentric bolt |
| q | Check wheel alignment whenever this component is loosened → Chapter. |
| q | Do not turn more than 90° in either direction (i.e. from minimum to maximum adjustment position). |
| 2 - | Nut |
| q | 95 Nm |
| q | Self-locking |
| q | Can be loosened and tightened up to 5 times for adjustment work |
| q | Always renew after removing. |
| q | Always tighten threaded connections in unladen position → Chapter |
| 3 - | Eccentric washer |
| q | Inner hole with lug |
| 4 - | Eccentric bolt |
| q | Check wheel alignment whenever this component is loosened → Chapter. |
| q | Do not turn more than 90° in either direction (i.e. from minimum to maximum adjustment position). |
| 5 - | Eccentric washer |
| q | Inner hole with lug |
| 6 - | Nut |
| q | 95 Nm |
| q | Self-locking |
| q | Can be loosened and tightened up to 5 times for adjustment work |
| q | Always renew after removing. |
| q | Always tighten threaded connections in unladen position → Chapter |
Note| t | To tighten nuts, set torque wrench -V.A.G 1332- to 80 Nm. |
| t | This torque setting only applies in conjunction with 18 mm tool insert -T10179- |
| 7 - | Subframe |
| 8 - | Bolt |
| q | 90 Nm + 90° further |
| q | Always renew after removing. |
| 9 - | Lower transverse link |
| q | Removing and installing → Chapter. |
| 10 - | Nut |
| q | 90 Nm + 90° further |
| q | Self-locking |
| q | Always renew after removing. |
| q | Always tighten threaded connections in unladen position → Chapter |
| 11 - | Bolt |
| q | Always renew after removing. |
| 12 - | Threaded rivet |
| q | M6 |
| 13 - | Spreader rivet |
| 14 - | Stone deflector |
| 15 - | Hexagon bolt |
| q | 8 Nm |
| 16 - | Nut |
| q | Self-locking |
| q | Always renew after removing. |
| q | Always tighten threaded connections in unladen position → Chapter |
| 17 - | Washer |
| 18 - | Bolt |
| q | 130 Nm + 90° further |
| q | Always renew after removing. |
| q | Always tighten threaded connections in unladen position → Chapter |
| 19 - | Washer |
| 20 - | Upper transverse link |
| q | Removing and installing → Chapter. |
| 21 - | Washer |
| 22 - | Nut |
| q | Self-locking |
| q | Always renew after removing. |
| 23 - | Wheel bearing housing |
| q | Removing and installing → Chapter. |
| 24 - | Washer |
| 25 - | Bolt |
| q | 130 Nm + 90° further |
| q | Always renew after removing. |
| q | Always tighten threaded connections in unladen position → Chapter |
| 26 - | Track rod |
| q | Open side downwards |
| q | Removing and installing → Chapter. |
| 27 - | Bolt |
| q | 90 Nm + 90° further |
| q | Always renew after removing. |
| 28 - | Bolt |
| q | Always renew after removing. |
| q | Always tighten threaded connections in unladen position → Chapter |
| 29 - | Nut |
| q | 90 Nm + 90° further |
| q | Self-locking |
| q | Always renew after removing. |
