Polo Mk4
|
| 1 - | Selector lever knob |
| q | Turn the sleeve 90° -2- and pull the knob upwards |
| 2 - | Sleeve |
| q | In the vehicle, it is a single part with the knob |
| q | By turning it, the selector lever knob is immobilized |
| 3 - | Cover |
| 4 - | Selector lever position indicator |
| q | With selection scale |
| q | The indicator contacts end up facing the contact spring -25- of the selector lever |
| q | Couple the plate cable for lighting and the cable that leads to the connector in their respective compartments within the frames |
| q | Unplug and plug the connector → Chapter |
| 5 - | Frame |
| q | Carefully separate by the borders making a lever |
| q | Pay attention to the assembly position of the circuit boards and the cables -4- |
| q | When placing it, avoid damages to the contact spring -25- of the selector lever position indicator |
| 6 - | Support |
| q | Couple to the frame -5- along with the connector |
| 7 - | Screw, 7 Nm |
| q | To subject the ratchet spring -11- and the plate -10- to the frame |
| 8 - | Washer |
| 9 - | Blocking segment |
| q | Place over the centralizing elements of the selector lever case -15- |
| 10 - | Plate |
| 11 - | Ratchet spring with roller |
| q | Engage to the notch of the selector lever -12- |
| 12 - | Selector lever |
| q | With control rod, compression spring, notch, contact spring for the lever position indicator and blocking cable disengaging device |
| q | Disassemble and assemble → Chapter |
| 13 - | Roller |
| q | To disengage the blocking cable |
| 14 - | Adjusting washer |
| 15 - | Selector lever case |
| q | It is not necessary to disassemble it to change most of the parts, except when it comes to the selector lever or the electromagnet for blocking it. |
| 16 - | Supporting pin |
| q | With toothed |
| q | Grease the rod |
| q | Do not turn it when assembling the selector lever, just immobilize it |
| 17 - | Blocking connecting rod |
| q | For blocking cable |
| q | To block with the selector lever in the position "P" |
| 18 - | Washer |
| 19 - | Screw |
| 20 - | Gasket |
| q | Always replace |
| 21 - | Cover |
| q | For the selector lever case |
| 22 - | Screw |
| q | 14 units |
| 23 - | O-ring |
| q | Always replace |
| 24 - | Screw, 8 Nm |
| q | 2 units |
| 25 - | Contact spring |
| q | For the selector lever position indicator |
| 26 - | Screw, 4 Nm |
| q | To release and tighten it, place the selector lever in the position "P" |
| 27 - | Clip |
| 28 - | Steering lock |
| 29 - | Screw |
| q | 2 units |
| q | To fasten the electromagnet to the selector lever case |
| 30 - | Electromagnet for blocking the selector lever -N110- |
| q | Disassemble and assemble → Chapter |
| 31 - | Cable clamp |
| q | Fasten the electromagnet cable to the transmission lever case |
| q | Always replace |
| 32 - | Spring |
| 33 - | Retaining pin |
| 34 - | Nut, 13 Nm |
| q | Always replace |
| 35 - | Washer |
| 36 - | Nut, 25 Nm |
| q | 4 units |
| q | Always replace |
| 37 - | Blocking cable |
| q | For ignition key anti-extraction blocking |
| q | You must not fold |
| q | Disassemble and assemble → Chapter |
| q | Adjust → Chapter |
| q | Check the operation of the ignition key anti-extraction blocking → Chapter |
| 38 - | Adjusting washer |
| q | Always replace |
| q | To fasten the selector lever cable to the selector lever case |
| q | Assemble with the elbowed end facing the interior of the selector lever case |
| 39 - | Gasket |
| q | Always replace |
| 40 - | Selector lever cable |
| q | Do not fold nor twist |
| q | Change the selector lever cable if the protective sheath is damaged |
| q | Check and adjust → Chapter |
| q | Disassemble and assemble → Chapter |
| q | Lightly lubricate the pipes in the ends before assembling it |
| 41 - | Connecting rod |
| q | For selector axle |
| 42 - | Idler |
| q | To fasten the selector lever cable to the transmission |
| 43 - | Adjusting washer |
| q | Always replace |
