Polo Mk5: 6-speed Automatic Gearbox 09G Valve Body Removal and Installation
| Overview - valve chest |
| 1 - | ATF inspection plug |
| q | Checking ATF level and topping up → Chapter |
| q | Torque setting → Chapter |
| 2 - | Seal |
| q | Always renew |
| 3 - | Overflow pipe |
| q | Unscrew to drain ATF |
| q | Torque setting → Chapter |
| 4 - | Oil pan |
| q | Removing and installing → Chapter |
| 5 - | Bolt |
| q | Tighten oil pan bolts diagonally in several stages. |
| q | Torque setting → Chapter |
| 6 - | Seal |
| q | With spacer sleeves (qty. 8) |
| q | Examine before fitting |
| q | Renew brittle, cracked or deformed seal |
| 7 - | Magnet |
| q | Qty. 2 in depressions in pan |
| q | Clean oil pan before installing |
| 8 - | Bolt |
| q | For securing valve body in gearbox |
| q | Qty. 12, various lengths → Fig. |
| q | Always renew bolts |
| q | Torque setting → Chapter |
| 9 - | Bolt |
| q | Qty. 3 |
| q | For securing strainer to valve body |
| q | Torque setting → Chapter |
| 10 - | ATF strainer |
| q | Removing and installing → Chapter |
| 11 - | Valve body |
| q | Removing → Chapter |
| q | Installing → Chapter |
| q | Allocation → Electronic parts catalogue „ETKA“ |
| 12 - | Bolt |
| q | Torque setting → Chapter |
| 13 - | Bolt |
| q | Torque setting → Chapter |
| 14 - | Gearbox input speed sender -G182- |
| q | Removing and installing → Chapter |
| 15 - | Bolt |
| q | Torque setting → Chapter |
| 16 - | Gearbox output speed sender -G195- |
| q | Removing and installing → Chapter |
| 17 - | Gearbox housing |
| q | Shown here without gearbox oil cooler |
| 18 - | Breather cap |
| 19 - | Multifunction switch -F125- |
| q | Removing and installing → Chapter |
| q | Adjusting → Chapter |
| 20 - | Gearbox oil temperature sender -G93- |
| q | Integrated into wiring harness |
| q | Torque setting → Chapter |
| q | Removing and installing → Chapter |
| q | Cable routing → Chapter. |
| 21 - | Bolt |
| q | Torque setting → Chapter |
| 22 - | Bolt |
| q | Torque setting → Chapter |
| 23 - | Wiring harness for sender |
| q | With gearbox oil temperature sender -G93- |
| q | For gearbox input speed sender -G182- |
| q | For gearbox output speed sender -G195- |
| q | Always renew oil seal on connector housing |
| q | Removing and installing → Chapter |
| q | Cable routing → Chapter. |
| q | Allocation → Electronic parts catalogue „ETKA“ |
| 24 - | Seal |
| q | Always renew |
| 25 - | ATF drain plug |
| q | Torque setting → Chapter |
| 26 - | Selector lever |
| q | For selector shaft |
| q | Removing and installing → Anchor |
| 27 - | Washer |
| 28 - | Nut |
| q | Location: centring collar faces washer → Item |
| q | Torque setting → Chapter |
| 29 - | Spring |
| q | Allocation → Electronic parts catalogue „ETKA“ |
| 30 - | Damper piston |
| 31 - | Wiring harness for solenoid valves |
| q | Always renew oil seal on connector housing |
| q | Removing and installing → Chapter |
| q | Cable routing → Chapter. |
| 32 - | Bolt |
| q | Torque setting → Chapter |
