RSX L4-2.0L (VTEC) (2002)
/Page-217001.png)
Powertrain Control Module: Testing and Inspection
How to Set Readiness Codes
How to Set Readiness Codes
Malfunction Indicator Lamp (MIL) Indication (In relation to Readiness Codes)
The vehicle has certain "readiness codes" that are part of the on-board diagnostics for the emissions Systems. If the vehicle's battery has been
disconnected or gone dead, if the DTCs have been cleared, or if the ECM/PCM has been reset, these codes are reset. In some states, part of the emissions
testing is to make sure these codes are set to complete. If all of them are not set to complete, the vehicle may fail the emission test, or the test cannot be
finished.
To check if the readiness codes are complete, turn the ignition switch ON (II), but do not start the engine. The MIL will come on for 15-20 seconds. If it
then goes off, the readiness codes are complete. If it blinks several times, one or more readiness codes are not complete. To set readiness codes from
incomplete to complete, do the procedure for the appropriate code.
Catalytic Converter Monitor and Readiness Code
NOTES:
-
Do not turn the ignition switch off during the procedure.
-
All readiness codes are cleared when the battery is disconnected or when the ECM/PCM is cleared with the OBD II scan tool or Honda PGM
Tester.
-
Low ambient temperatures or excessive stop-and-go traffic may increase the drive time needed to switch the readiness code from incomplete to
complete.
-
The readiness code will not switch to complete until all the enable criteria are met.
-
If a fault in the secondary HO2S system caused the MIL to come on, the readiness code cannot be set to complete until you correct the fault.
Enable Criteria:
-
ECT at 158°F (70°C) or higher.
-
Intake air temperature (IAT) at 2O°F (-7°C) or higher.
-
Vehicle speed is steady, and vehicle speed sensor (VSS) reads more then 25 mph (40 km/h).
Procedure
1. Connect the scan tool to the vehicle's data link connector (DLC), and bring up the tool's generic OBD II mode.
2. Start the engine.
3. Test-drive the vehicle under stop-and-go conditions with short periods of steady cruise. After about 5 miles (8 km), the readiness code should
switch from incomplete to complete.
4. If the readiness code is still set to incomplete, check for a temporary DTC. If there is no DTC, one or more of the enable criteria were probably not
met; repeat the procedure.
Evaporative Emissions (EVAP) Control System Monitor and Readiness code
NOTES:
-
All readiness code are cleared when the battery is disconnected or when the ECM/PCM is cleared with the OBD II scan tool or Honda PGM
Tester.
-
The enable criteria must be repeated if the intake air temperature (IAT) drops lower then 36^F (20^C) from its value at engine start up.
Enable Criteria
-
At engine start up, ECT and IAT are higher then 32°F (0°C), but lower then 95°F (35°C).
-
At engine start up, the ECT and AT are within 12°F (7°C) of each other.
Procedure
1. Connect the scan tool to the vehicle's data link connector (DLC), and bring up the tool's generic OBD II mode.
2. Start the engine.
3. Test-drive the vehicle under stop-and-go conditions with short periods of steady cruise. After about 2.5 miles (4.0 km), the readiness code should
switch from incomplete to complete.
4. If the readiness code is still set to incomplete, check for a temporary DTC. If there is no DTC, one or more of the enable criteria were probably not
met; repeat the procedure.
Air Fuel Ratio (A/F) Sensor Monitor and Readiness Code
NOTE:
-
Do not turn the ignition switch off during the procedure.
-
All readiness codes are cleared when the battery is disconnected or when the ECM/PCM is cleared with the OBD II scan tool or Honda PGM
Tester.
