Fault table
Fault table
|
---|
Output on printer V.A.G 1551
|
Possible cause of fault
|
Rectifying fault
|
00258
|
|
Wiring open or short circuit
|
- Check wiring and connections according to current flow diagram2)
|
Solenoid valve 1 -N88-
|
|
Solenoid valve 1 -N88- defective
|
- Read measured value block ; display group number 004
|
Short to earth1) Open circuit/short to earth1)
|
|
|
00260
|
|
Wiring open or short circuit
|
- Check wiring and connections according to current flow diagram2)
|
Solenoid valve 2 -N89-
|
|
Solenoid valve 2 -N89- defective
|
- Read measured value block ; display group number 004
|
Short to earth1) Open circuit/short to earth1)
|
|
|
1) One of these displays appears in addition to relevant component.
2) First check connections for contact corrosion or water ingress and renew if necessary. If solenoid faults are displayed then especially check the connection on top of gearbox and solenoid valve wiring harness.
|
---|
Output on printer V.A.G 1551
|
Possible cause of fault
|
Rectifying fault
|
00262
|
|
Wiring open or short circuit
|
- Check wiring and connections according to current flow diagram2)
|
Solenoid valve 3 -N90-
|
|
Solenoid valve 3 -N90- defective
|
- Read measured value block ; display group number 004
|
Short to earth1) Open circuit/short to earth1)
|
|
|
00264
|
|
Wiring open or short circuit
|
- Check wiring and connections according to current flow diagram2)
|
Solenoid valve 4 -N91-
|
|
Solenoid valve 4 -N91- defective
|
- Read measured value block ; display group number 003
|
Short to earth1) Open circuit/short to earth1)
|
|
|
1) One of these displays appears in addition to relevant component.
2) First check connections for contact corrosion or water ingress and renew if necessary. If solenoid faults are displayed then especially check the connection on top of gearbox and solenoid valve wiring harness.
Output on printer V.A.G 1551
|
Possible cause of fault
|
Rectifying fault
|
00266
|
|
Wiring open or short circuit
|
- Check wiring and connections according to current flow diagram2)
|
Solenoid valve 5 -N92-
|
|
Solenoid valve 5 -N92- defective
|
- Read measured value block ; display group number 004
|
Short to earth1) Open circuit/short to earth1)
|
|
|
00268
|
|
Wiring open or short circuit
|
- Check wiring and connections according to current flow diagram2)
|
Solenoid valve 6 -N93-
|
|
Solenoid valve 6 -N93- defective
|
- Read measured value block ; display group number 002
|
Short to earth1) Open circuit/short to earth1)
|
|
|
1) One of these displays appears in addition to relevant component.
2) First check connections for contact corrosion or water ingress and renew if necessary. If solenoid faults are displayed then especially check the connection on top of gearbox and solenoid valve wiring harness.
Output on printer V.A.G 1551
|
Possible cause of fault
|
Rectifying fault
|
00281
|
|
Wiring open circuit
|
|
Road speed sender -G68-
No signal
|
|
Road speed sender -G68- defective
|
- Read measured value block ; display group number 001 Check wiring and connections using current flow diagram2)
|
00293
Multi-function switch -F125-
|
|
Wiring open circuit
|
- First check multi-function switch connector for contact corrosion or water ingress, renew if necessary
|
Undefined switch condition
|
|
Multi-function switch -F125- defective
|
- Read measured value block ; display group number 004
|
00296
Kickdown switch
Short to earth1) Implausible signal1)
|
|
Signal is continuously sent from EPC although the accelerator pedal is not pressed to stop.
|
- Read measured value block ; display group number 004
|
1) One of these displays appears in addition to relevant component.
2) First check connections for contact corrosion or water ingress and renew if necessary. If solenoid faults are displayed then especially check the connection on top of gearbox and solenoid valve wiring harness.
|
---|
Output on printer V.A.G 1551
|
Possible cause of fault
|
Rectifying fault
|
00300
|
|
Wiring open circuit
|
- Check wiring and connections according to current flow diagram2)
|
Gearbox oil temperature sender -G93-1)
|
|
Gearbox oil temperature sender -G93- defective
|
- Read measured value block ; Display group number 002
|
Open/short circuit to positive
|
|
-
|
1) A faulty ATF temperature sender is indicated.
2) First check connections for contact corrosion or water ingress and renew if necessary. If solenoid faults are displayed then especially check the connection on top of gearbox and solenoid valve wiring harness.
Output on printer V.A.G 1551
|
Possible cause of fault
|
Rectifying fault
|
00347
|
|
Wiring open or short circuit
|
- Check wiring and connections using current flow diagram
|
Solenoid valve 8 -N281-
|
|
Solenoid valve 8 -N281- defective
|
- Read measured value block ; display group number 004
|
Short to earth1) Open circuit/short to earth1)
|
|
|
00348
|
|
Wiring open or short circuit
|
- Check wiring and connections using current flow diagram2)
|
Solenoid valve 9 -N282-
|
|
Solenoid valve 9 -N282- defective
|
- Read measured value block ; display group number 004
|
Short to earth1) Open circuit/short to earth1)
|
|
|
1) One of these displays appears in addition to relevant component.
2) First check connections for contact corrosion or water ingress and renew if necessary. If solenoid faults are displayed then especially check the connection on top of gearbox and solenoid valve wiring harness.
|
---|
Output on printer V.A.G 1551
|
Possible cause of fault
|
Rectifying fault
|
00349
|
|
Wiring open or short circuit
|
- Check wiring and connections using current flow diagram2)
|
Solenoid valve 10 -N283-
|
|
Solenoid valve 10 -N283- defective
|
- Read measured value block ; display group number 008
|
Short to earth1) Open circuit/short to earth1)
|
|
|
00350
|
|
Wiring open circuit
|
- Check wiring and connections using current flow diagram2)
|
Earth return wire, modulation valve
Output does not switch/short to positive
|
Control unit -J217- defective
|
- Renew control unit
|
1) One of these displays appears in addition to relevant component.
2) First check connections for contact corrosion or water ingress and renew if necessary. If solenoid faults are displayed then especially check the connection on top of gearbox and solenoid valve wiring harness.
Output on printer V.A.G 1551
|
Possible cause of fault
|
Rectifying fault
|
00351
|
|
Wiring open or short circuit
|
- Check wiring and connections using current flow diagram1)
|
Intermediate shaft speed sender -G265-
No signal
|
|
Intermediate shaft speed sender -G265- defective
|
- Read measured value block ; display group number 007
|
00529
Speed information missing
No signal
|
|
The engine control unit identifies the signal as faulty and then sends it into the data bus.
|
If the readout also shows fault codes 01312 or 01314, rectify these faults first Check engine control unit =>see engine Workshop Manual; Repair group 01; Performing self-diagnosis Read measured value block; Display group No. 001 Check wiring and connections according to Current flow diagram
|
00532
|
|
Battery defective
|
- Test battery voltage
|
Supply voltage
|
|
Insufficient system voltage for valves
|
- Read measured value block ; display group number 002
|
1) First check connections for contact corrosion or water ingress and renew if necessary. Pay particular attention to the connections on the gearbox.
|
---|
Output on printer V.A.G 1551
|
Possible cause of fault
|
Rectifying fault
|
00652
Gear monitoring
|
|
Electrical/hydraulic fault
Clutch or valve chest defective
|
- Read measured value block ; display group number 001 and establish in which gear the fault occurs by driving
|
Implausible signal1) Mechanical fault1)
|
|
|
|
00777
|
|
- Check engine control unit => see engine Workshop Manual; Repair group 01; Performing self-diagnosis
|
Accelerator pedal position sender -G79-
No signal
|
|
The engine control unit identifies the signal as faulty and then sends it into the data bus.
|
- Read measured value block
|
01045
Tiptronic switch -F189-
Implausible signal
|
|
Wiring open circuit
Tiptronic switch -F189- defective
|
- Check wiring and connections using current flow diagram Read measured value block ; display group 005
|
1) One of these displays appears in addition to relevant component.
Output on printer V.A.G 1551
|
Possible cause of fault
|
Rectifying fault
|
01166
|
|
|
-
|
No signal 1) Implausible signal 1) Signal outside tolerance 1)
|
|
The engine control unit identifies the signal as faulty and then sends it into the data bus.
|
- Perform self-diagnosis of engine control unit => see engine Workshop Manual; Repair group 01; Performing self-diagnosis
|
01192
|
|
|
|
Torque converter lock-up clutch
Mechanical fault1) Defective1)
|
Lock-up clutch slips Valve chest defective
|
- Check torque converter lock-up clutch slip Read measured value block ; display group number 003
|
01236
|
|
|
|
Selector lever lock solenoid -N110-
Short to earth1) Open circuit/short to positive1)
|
Wiring open circuit or short Selector lever lock solenoid -N110- defective
|
- Read measured value block ; display group number 004
|
1) One of these displays appears in addition to relevant component.
|
---|
Output on printer V.A.G 1551
|
Possible cause of fault
|
Rectifying fault
|
01312
|
|
|
|
Drive train data bus
Defective1) No communication1)
|
Data bus wiring/connectors defective
|
- Read measured value block ; display group 125
|
01314
|
|
|
|
Engine control unit
No communication1)
|
Data bus wiring/connectors defective
|
- Read measured value block => Page 01-52; display group 125
|
Wrong equipment1)
|
Engine control unit incorrectly coded
|
Perform self-diagnosis of engine control unit => see engine Workshop Manual; Repair group 01; Performing self-diagnosis
|
1) One of these displays appears in addition to relevant component.
Output on printer V.A.G 1551
|
Possible cause of fault
|
Rectifying fault
|
01316
|
|
|
|
Brake control unit No communication
|
Data bus wiring/connectors defective
|
- Read measured value block => Page 01-52; display group 125
|
018108
|
|
|
-
|
Brake pressure switch -F270-
Implausible signal
|
|
Wiring open circuit Switch -F270- defective
|
- Read measured value block => Page 01-52; display group 004
|
|
---|
Output on printer V.A.G 1551
|
Possible cause of fault
|
Rectifying fault
|
17101P0717
|
|
Wiring open circuit or short to earth or positive
|
- Check wiring and connectors using current flow diagram
|
Gearbox input speed sender -G182-
|
|
Screening for wiring to gearbox input speed sender -G182- defective Gearbox input speed sender -G182- defective
|
- Read measured value block =>page
|
No signal
|
|
Engine speed, gearbox speed signal defective Multi-function switch -F125- defective
|
- Perform fault elimination according to fault codes 00529 or 00293
|
|
|
ATF level not OK Defective torque converter
|
- Check ATF level
|
|
|
Clutches or brakes slipping Sticking solenoid valve
|
- Read measured value block ; Display group number 007 and then determine during a test drive which elements are defective or which are not activated
|
Output on printer V.A.G 1551
|
Possible cause of fault
|
Rectifying fault
|
65535
|
|
|
- Renew control unit
|
Control unit defective
|
|
Control unit -J217- defective
|
- Initiate basic setting
|
The control unit -J217- should not be renewed until the possible cause of the fault has been determined and the following faults have been rectified:
-
◆ mechanical faults
-
◆ hydraulic faults
-
◆ all affected electrical/electronic components and cable connections.
If the control unit is renewed, the system must be returned to its basic setting => Page 01-50.
|