|
→ Display on VAS 5051:
- 1 - Reading measured value block
- 2 - Display zone 1
- Display zone 2
- Display zone 3
- Display zone 4
- 3 - Display group X
Notes:
-
◆ Display remains blank if a display zone is not used.
-
◆ Proceed as follows to switch to a different display group:
|
|
|---|
|
Display group
|
VAS 5051
|
|
Up
|
Press s key
|
|
Down
|
Press t key
|
-
‒ Terminate function "08 - Reading measured value block" by touching◂key.
List of display groups
|
|
|---|
|
Display group number
|
Indicated on display
|
|
020
|
1 = 1st and 2nd ident no. position
2 = 3rd and 4th ident no. position
3 = 5th and 6th ident no. position
4 = 7th and 8th ident no. position
|
|
021
|
9 = 9th and 10th ident no. position
2 = 11th and 12th ident no. position
3 = 13th and 14th ident no. position
4 = Not used
|
|
022
|
1 = Starting authorised
2 = Engine control unit response
3 = Key status OK
4 = Not used
|
Measured value block 020
|
|
|
|
|
|
Display group 20
|
|
◂ Indicated on display
|
|
|
|
AU
|
Z7
|
Z0
|
T0
|
◂ Display zones 1 ... 4
|
|
|
|
|
|
|
|
7th and 8th ident no. position
|
|
|
|
|
|
|
5th and 6th ident no. position
|
|
|
|
|
|
3rd and 4th ident no. position
|
|
|
|
|
1st and 2nd ident no. position
|
|
|
|
|
|
Measured value block 021
|
|
|
|
|
|
Display group 21
|
|
◂ Indicated on display
|
|
|
|
03
|
38
|
77
|
-
|
◂ Display zones 1 ... 4
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
13th and 14th ident no. position
|
|
|
|
|
|
11th and 12th ident no. position
|
|
|
|
|
9th and 10th ident no. position
|
|
|
|
|
|
Measured value block 022
|
|
|
|
|
|
Display group 22
|
|
◂ Indicated on display
|
|
|
|
X
|
X
|
X
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Key status OK
▪ 1 = Yes
▪ 0 = No, i.e. vehicle key not/incorrectly matched or transponder defective
|
|
|
|
|
|
Engine control unit response 1)
▪ 1 = Yes
▪ 0 = No, i.e. fault in engine control unit or wiring
|
|
|
|
|
Starting authorised
▪ 1 = Yes
▪ 0 = No, i.e. vehicle key not/incorrectly matched or engine control unit incorrectly encoded/defective
|
|
|
|
|
|
1) Depending on engine control unit, measured value block is set for 10 ... 30 s after switching off engine and ignition to "0 = Engine control unit response no", i.e. engine control unit released and no fault present. Start self-diagnosis again as a check => Page 01-241.
|
