audi Workshop Repair Guides

Audi Workshop Service and Repair Manuals

ABOUT US
Removing and installing oil pan > < Removing and installing gear oil filter

A3 Mk2

Exploded view - oil pan, mechatronic unit, gear oil pump
   
Exploded view - oil pan, mechatronic unit, gear oil pump
  Note
t  -Items 8 ... 14- can be disregarded here. For description see → Chapter „Exploded view - gear oil cooler and gear oil filter“.
t  -Items 19 ... 23- can be disregarded here. For description see → Chapter „Exploded view - drain plug, inspection plug and overflow pipe for gear oil“.
1 - Oil pan
q   → Chapter „Removing and installing oil pan“
2 - Bolt
q   5x
q   Renew
q   → Fig. „Oil pan - tightening torque and sequence “
3 - Gasket
q   Renew
4 - Bolt
q   10x
q   Renew
q   → Fig. „Mechatronic unit for dual clutch gearbox -J743-: tightening torque and sequence“
5 - Mechatronic unit for dual clutch gearbox -J743-
q   With O-rings on connector
q   Renew O-rings
q   → Chapter „Removing and installing mechatronic unit for dual clutch gearbox -J743-“
6 - Breather pipe
q   Pressed into gearbox
q   Must be renewed if removed
7 - Breather cap
q   Fitted onto breather pipe
15 - Gear oil pump
q   → Chapter „Removing and installing gear oil pump“
q   Install with new gasket
16 - Bolt
q   4x
q   Different bolts according to version
q   Renew
q   → Fig. „Gear oil pump - tightening torque and sequence “
17 - Cover for gear oil pump
q   With gasket
q   Renew
q   Removing and installing → Chapter „Removing and installing gear oil pump“
18 - Bolt
q   4x
q   Renew
q   → Fig. „Cover -A- for gear oil pump - tightening torque and sequence “
24 - Guard plate
q   Depending on version
25 - Bolt
q   4x
q   32 Nm

   
Oil pan - tightening torque and sequence
–  Tighten bolts -arrows- diagonally in stages to 16 Nm.
  A37-0672
Mechatronic unit for dual clutch gearbox -J743-: tightening torque and sequence
  Note
Renew bolts which are tightened by turning through a specified angle.
–  Tighten bolts in 4 stages in the sequence shown:
  N35-10101
StageBoltsTightening torque/tightening angle
1.-1 … 10-Screw in bolts by hand until they make contact
2.Remove guide pin -T40199- 
3.-1 … 10-5 Nm
4.-1 … 10-Turn 90° further

   
Gear oil pump - tightening torque and sequence
  Note
Renew bolts which are tightened by turning through a specified angle.
–  Tighten bolts -arrows- (different bolts according to version):
Countersunk-head bolts -A-:
–  Tighten countersunk head bolts in diagonal sequence to 8 Nm.
Pan-head bolts -B-:
–  Tighten pan-head bolts in 2 stages as follows:
  A37-10735
StageBoltsTightening torque/tightening angle
1.-B-5 Nm in diagonal sequence
4.-B-Turn 90° further in diagonal sequence

   
Cover -A- for gear oil pump - tightening torque and sequence
  Note
Renew bolts securing cover for gear oil pump.
–  Tighten bolts -arrows- diagonally in stages to 8 Nm.
  A37-0670
Gearbox input speed sender -G182-/clutch temperature sender -G509-
A - Gearbox input speed sender -G182-/clutch temperature sender -G509-
B - Bolt, 10 Nm
C - Electrical connector
→ Chapter „Removing and installing gearbox input speed sender -G182-/oil temperature sender for multi-plate clutch -G509-“.
  A37-0676

Removing and installing oil pan > < Removing and installing gear oil filter