A3 Mk2
Note
|
1 - | Intake manifold flap motor -V157- |
q | Removing and installing → Chapter |
2 - | Mechanical exhaust gas recirculation valve |
3 - | Engine control unit |
q | Removing and installing → Chapter |
4 - | Unit injectors |
q | Unit injector solenoid valve, No. 1 cyl. -N240- |
q | Unit injector solenoid valve, No. 2 cyl. -N241- |
q | Unit injector solenoid valve, No. 3 cyl. -N242- |
q | Unit injector solenoid valve, No. 4 cyl. -N243- |
q | Removing and installing unit injectors → Chapter |
5 - | Changeover flap for exhaust gas recirculation |
6 - | Air mass meter -G70- |
7 - | Solenoid valve block |
q | With exhaust gas recirculation valve -N18- |
q | With solenoid valve for charge pressure control -N75- |
q | With exhaust gas recirculation cooler change-over valve -N345- |
q | Fitting location → Fig. |
8 - | Engine electronics warning lamp -K149- |
q | In instrument cluster |
9 - | Accelerator position sender -G79- with accelerator position sender 2 -G185- |
q | Fitting location → Fig. |
10 - | Brake light switch -F- and brake pedal switch -F63- |
q | Fitting location: |
Vehicles up to approx. 11.2005 → Fig. |
Vehicles from approx. 11.2005 onwards → Fig. (gradual introduction) |
11 - | 5-position relay carrier in dash panel on driver's side (bottom left) |
q | With fuel pump relay -J17- (depending on version) |
q | For identification of socket position refer to → Current flow diagrams, Electrical fault finding and Fitting locations |
12 - | Clutch position sender -G476- |
q | Fitting location → Fig. |
13 - | Relay and fuse holder in electronics box in engine compartment |
q | With terminal 30 voltage supply relay -J317- |
q | With terminal 15 voltage supply relay -J329- |
q | For identification of socket position refer to → Current flow diagrams, Electrical fault finding and Fitting locations |
14 - | Automatic glow period control unit -J179- |
q | Fitting location → Fig. |
15 - | Coolant temperature sender -G62- |
q | Fitting location → Fig. |
q | If necessary release pressure in cooling system before removing |
16 - | Tandem pump |
q | Removing, installing and checking → Rep. Gr.20 |
17 - | Radiator outlet coolant temperature sender -G83- |
q | Fitting location → Fig. |
18 - | Multi-pin connector |
q | For unit injectors |
q | Fitting location → Fig. |
19 - | Engine speed sender -G28- |
q | Fitting location → Fig. |
20 - | Fuel temperature sender -G81- |
q | Fitting location → Fig. |
21 - | Glow plugs |
q | Glow plug 3 -Q12- |
q | Glow plug 4 -Q13- |
q | Removing and installing → Chapter |
22 - | 3-pin connector |
q | For Hall sender -G40- |
q | Fitting location → Fig. |
23 - | Glow plugs |
q | Glow plug 1 -Q10- |
q | Glow plug 2 -Q11- |
q | Removing and installing → Chapter |
24 - | Charge pressure sender -G31- with intake air temperature sender -G42- |
q | Fitting location → Fig. |
25 - | Hall sender -G40- |
q | For camshaft position |
q | Fitting location → Fig. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|