A3 Mk2
|
1 - | Pressure differential sender -G505- |
q | Exploded view → Chapter |
q | If renewed, learnt values must be reset |
2 - | Hall sender -G40- |
q | Fitting location → Fig. |
q | 10 Nm |
3 - | Injectors |
q | Exploded view → Chapter |
4 - | Engine control unit -J623- |
q | Fitting location → Fig. |
5 - | Lambda probe -G39- with Lambda probe heater -Z19- |
q | Exploded view → Chapter |
q | 50 Nm |
6 - | Position sender for charge pressure positioner -G581- |
q | Fitting location → Fig. |
7 - | Exhaust gas recirculation control motor -V338- with exhaust gas recirculation potentiometer -G212- |
q | Integrated into exhaust gas recirculation cooler |
q | Fitting location → Fig. |
q | Removing and installing → Engine, mechanics; Rep. gr.26 |
8 - | Fuel pressure regulating valve -N276- |
q | Exploded view → Chapter |
q | Checking → Chapter |
9 - | Charge pressure control solenoid valve -N75- |
q | Fitting location → Fig. |
10 - | Electrical connector |
q | For exhaust gas temperature sender 4 -G648- |
q | For exhaust gas temperature sender 1 -G235- |
q | For Lambda probe -G39- |
q | Fitting location → Fig. |
11 - | Air mass meter -G70- |
q | Exploded view → Chapter |
12 - | Coolant temperature sender -G62- |
q | Fitting location → Fig. |
13 - | Engine speed sender -G28- |
q | Fitting location → Fig. |
q | 4.5 Nm |
14 - | Exhaust gas recirculation cooler change-over valve -N345- |
q | Fitting location → Fig. |
15 - | Pump for exhaust gas recirculation cooler -V400- |
q | Fitting location → Fig. |
16 - | Throttle valve module -J338- with throttle valve potentiometer -G69- |
q | Exploded view → Chapter |
17 - | Glow plugs |
q | Glow plug 1 -Q10- |
q | Glow plug 2 -Q11- |
q | Glow plug 3 -Q12- |
q | Glow plug 4 -Q13- |
q | Removing and installing → Chapter |
q | 17 Nm |
18 - | Fuel temperature sender -G81- |
q | In fuel supply line |
q | Fitting location → Fig. |
19 - | High-pressure pump with fuel metering valve -N290- |
q | Exploded view → Chapter |
q | Do not open fuel metering valve -N290- |
q | After renewing, first fuel filling operation MUST be performed (it is important not to allow pump to run while it is still empty) → Chapter |
20 - | Charge pressure sender -G31- with intake air temperature sender -G42- |
q | Fitting location → Fig. |
21 - | Fuel pressure sender -G247- |
q | Exploded view → Chapter |
22 - | Radiator outlet coolant temperature sender -G83- |
q | Fitting location → Fig. |
23 - | Fuel filter |
q | Exploded view → Rep. gr.20 |
q | Renewing → Rep. gr.20 |
24 - | Supplementary fuel pump -V393- |
q | Exploded view → Rep. gr.20 |
A - | Low heat output relay -J359- and high heat output relay -J360- |
q | Fitting location → Current flow diagrams, Electrical fault finding and Fitting locations |
B - | Brake light switch -F- and brake pedal switch -F47- |
q | Fitting location → Fig. |
C - | Clutch position sender -G476- |
q | Fitting location → Fig. |
q | Only fitted on vehicles with manual gearbox |
D - | Accelerator position sender -G79- and accelerator position sender 2 -G185- |
q | Fitting location → Fig. |
E - | Exhaust gas temperature sender 1 -G235- |
q | Exploded view → Chapter |
F - | Exhaust gas temperature sender 3 -G495- |
q | Exploded view → Chapter |
G - | Exhaust gas temperature sender 4 -G648- |
q | Exploded view → Chapter |
H - | Particulate filter |
q | Combined with catalytic converter |
q | Adaption must be performed after renewing this component |
q | Removing and installing → Rep. gr.26 |
|
Note
|
|
|
|
|
|
|
|
|
|
|
|
|
|