audi Workshop Repair Guides

Audi Workshop Service and Repair Manuals

ABOUT US
Ignition system, glow plug system > < Testing brake light switch -F and brake pedal switch -F47

A4 Mk1

Simos injection and ignition system (4-cylinder)
Testing accelerator position senders
Testing clutch pedal switch -F36
 
G24-0023

Special tools and workshop equipment required

  • ◆ V.A.G 1526 A
  • ◆ V.A.G 1527 B
  • ◆ V.A.G 1594 A
  • ◆ V.A.G 1598/31
  • ◆ VAS 5051 with VAS 5051/1
  • or
  • ◆ V.A.G 1551 with V.A.G 1551/3 A

Note:

This signal is used to avoid over-revving and load change jolts when disengaging the clutch. It is also needed for the cruise control system.

Test sequence

  • ‒ Connect vehicle diagnostic, testing and information system VAS 5051 (or fault reader V.A.G 1551) and select engine electronics control unit by entering address word "01" ( .)
    When doing this the ignition must be switched on.
 
→ Indicated on display:
Rapid data transfer    HELP
Select function XX
  • ‒ Press keys 0 and 8 for the function "Read measured value block" and confirm entry with Q key.
 
→ Indicated on display:
Read measured value block    
Enter display group number XXX
  • ‒ Press keys 0, 6 and 6 to select "Display Group 66" and confirm entry with the Q key.
 
→ Indicated on display:
Read measured value block 66    ⇒
    1    2    3    4
  • ‒ Observe display in display zone 2.

Display zones

1

2

3

4

Display group 66: Signals to engine control unit

Display

xxx km/h

0 0 0 0

xxx km/h

0 0 0 0

Indicates

Actual speed

Switch positions

Specified speed

Switch positions for cruise control system

Range


off = 0
on = 1


off = 0
on = 1

Specification

0 0 0 0

Note

Relevance of figures
=> Page 24-191

  • ‒ Depress clutch pedal

Relevance of figures in 4-digit readout in display zone 2

x

x

x

x

Display zone 2

X

Brake light switch
0 = Brake pedal not depressed
1 = Brake pedal depressed

X

Brake pedal switch
0 = Brake pedal not depressed
1 = Brake pedal depressed

X

Clutch pedal switch
0 = Clutch pedal not depressed
1 = Clutch pedal depressed

X

Cruise control system (CCS)
0 = CCS deactivated
1 = CCS enabled

Display zones

1

2

3

4

Display group 66: Signals to engine control unit

Display

xxx /rpm

0 1 0 0

xxx km/h

0 0 0 0

Indicates

Actual engine speed

Switch positions

Switch positions for cruise control system

Range


off = 0
on = 1


off = 0
on = 1

Specification

0 1 0 0

Note

Readout must change from 0 to 1

  • ‒ Allow clutch pedal to return slowly to its normal position.
  • ‒ Readout should return from 1 to 0.

If the readout does not change:

  • ‒ Test voltage supply => Page 24-193.

Testing voltage supply

  • ‒ Remove storage compartment on driver's side.

=> General body repairs, Interior; Repair group 68; Dash panel; Removing driver's storage compartment

  • ‒ Unplug 2-pin connector from clutch pedal.
  • ‒ Switch on ignition.
  • ‒ Connect hand-held multimeter (voltage range) between the following sockets on the connector:

2-pin connector on
wiring harness, socket

Specification

2 + earth

Battery voltage

If specification is obtained:

  • ‒ Test wiring connections => Page 24-194.

If specification is not obtained:

  • ‒ Test wiring from socket 2 of connector for open circuit and short to earth:

=> Current flow diagrams, Electrical fault finding and fitting locations binder

Testing wiring connection

  • ‒ Connect test box V.A.G 1598/31 to wiring harness for engine control unit. Do not connect to the engine control unit itself.
    => Page 24-26.

Test the following wiring connections for open circuits and short to positive or earth.

2-pin connector on
wiring harness, socket

Test box V.A.G 1598/31, socket

1

65

Resistance in wiring: max. 1.5 Ohm

  • ‒ Rectify any open/short circuit as necessary.

=> Current flow diagrams, Electrical fault finding and fitting locations binder

If no open circuits are found in wiring:

  • ‒ Renew clutch pedal switch.

Ignition system, glow plug system > < Testing brake light switch -F and brake pedal switch -F47