A5
| Exploded view of upper transverse link, track rod, coil spring, lower transverse link, vehicle level sender |
| 1 - | Bolt |
| q | 70 Nm +180° |
| q | Always renew if removed |
| q | Vehicle must be in unladen position when tightening → Chapter |
| 2 - | Retaining bracket |
| 3 - | Rear left vehicle level sender -G76- |
| q | The same sender versions must be installed on both sides. |
| q | Complete with mounting parts |
| q | Lever of sender faces outwards |
| q | Renewing in vehicle → Chapter |
| q | Check basic adjustment of headlights if sender mountings are loosened → Rep. gr.94 |
| q | If, on vehicles with electronic damping control, the vehicle level sender has been removed and refitted or the linkage detached, the reference position must be re-adapted → Chapter. → Vehicle diagnostic tester |
| q | If the reference position has been re-adapted on vehicles with lane departure warning, the lane departure warning control unit -J759- must be recalibrated → Chapter. |
| 4 - | Subframe |
| 5 - | Bolt |
| q | 70 Nm +180° |
| q | Always renew if removed |
| q | Vehicle must be in unladen position when tightening → Chapter |
| 6 - | Upper transverse link |
| q | Removing and installing → Chapter |
| 7 - | Nut |
| q | Always renew if removed |
| 8 - | Shim |
| 9 - | Nut |
| q | 95 Nm |
| q | Always renew if removed |
| q | Vehicle must be in unladen position when tightening → Chapter |
| 10 - | Adjuster screw |
| 11 - | Lower transverse link |
| q | Removing and installing → Chapter |
| 12 - | Bolt |
| q | 120 Nm +360° |
| q | Always renew if removed |
| q | Vehicle must be in unladen position when tightening → Chapter |
Note| Wheel alignment must be checked if bolt is removed. |
| 13 - | Spacer for top spring seat |
| 14 - | Top spring seat |
| q | Only fitted on heavy-duty running gear version and Sportback |
| 15 - | Coil spring |
| q | Note different running gear versions; see vehicle data sticker → Chapter |
| q | Removing and installing → Chapter |
| 16 - | Bottom spring seat |
| 17 - | Stone deflector for coil spring |
| 18 - | Wheel bearing housing |
| 19 - | Spacer |
| q | Always renew if removed |
| 20 - | Nut |
| q | Always renew if removed |
Caution
|
Note| Wheel alignment must be checked if nut is slackened. |
| 21 - | Bolt |
| q | 90 Nm +90° |
| q | Always renew if removed |
| q | Vehicle must be in unladen position when tightening → Chapter |
| 22 - | Track rod |
| q | Removing and installing → Chapter |
| q | Note correct installation position |
| q | Different versions (aluminium and steel); for correct version, refer to → Electronic parts catalogue |
| q | Mixed installation is not permissible |
| 23 - | Bolt |
| 24 - | Eccentric washer |
| 25 - | Nut |
| q | 95 Nm |
| q | Always renew if removed |
| q | Vehicle must be in unladen position when tightening → Chapter |
| 26 - | Bolt |
| q | 70 Nm +180° |
| q | Always renew if removed |
| q | Vehicle must be in unladen position when tightening → Chapter |
| 27 - | Nut |
| q | Always renew if removed |
| 28 - | Bolt |
| q | 9 Nm |
| 29 - | Bolt |
| q | 5 Nm |