chevrolet Workshop Repair Guides

Chevrolet Workshop Service and Repair Manuals

Ring Gear, Differential > < Drive Pinion Housing and/or Seal Replacement|Page 15708
Page 3
background image

2. Install the new ring gear bolts.

Hand start each bolt to ensure that the ring gear is properly installed to the differential case.

Notice:  Refer to Fastener Notice   .

3. Tighten the ring gear bolts. Tighten the ring gear bolts alternately and in stages, gradually pulling the ring gear onto the differential case.

*

For the 8.6 inch axle, tighten the ring gear bolts in sequence to 120 N.m (89 lb ft).

*

For the 9.5LD inch axle, tighten the ring gear bolts in sequence to 140 N.m (103 lb ft).

4. Install the pinion bearing cups. Refer to Drive Pinion Bearings Replacement (10.5 Inch Axle)  (See: Pinion Bearing/Service and Repair/Drive

Pinion Bearings Replacement (10.5 Inch Axle))Drive Pinion Bearings Replacement (8.6, 9.5, 11.5 Inch Axle)  (See: Pinion Bearing/Service and
Repair/Drive Pinion Bearings Replacement (8.6, 9.5, 11.5 Inch Axle)) .

5. Determine the selective shim thickness for the pinion gear. Refer to Pinion Depth Adjustment (10.5 Inch Axle)  (See: Service and Repair/Removal

and Replacement/Pinion Depth Adjustment (10.5 Inch Axle))Pinion Depth Adjustment (8.6, 9.5LD Axle)  (See: Service and Repair/Removal and
Replacement/Pinion Depth Adjustment (8.6, 9.5LD Axle)) .

6. Install the selective shim onto the pinion.
7. Install the inner pinion bearing to the pinion. Refer to Drive Pinion Bearings Replacement (10.5 Inch Axle)  (See: Pinion Bearing/Service and

Repair/Drive Pinion Bearings Replacement (10.5 Inch Axle))Drive Pinion Bearings Replacement (8.6, 9.5, 11.5 Inch Axle)  (See: Pinion
Bearing/Service and Repair/Drive Pinion Bearings Replacement (8.6, 9.5, 11.5 Inch Axle)) .

8. Install a new collapsible spacer.
9. Lubricate the pinion bearings with axle lubricant. Refer to Fluid and Lubricant Recommendations   .

10. Install the outer pinion bearing into the axle housing.
11. Install the new pinion oil seal. Refer to Drive Pinion Flange/Yoke and/or Oil Seal Replacement (8.6/9.5 Inch Axle)  (See: Pinion Flange/Service

and Repair/Drive Pinion Flange/Yoke and/or Oil Seal Replacement (8.6/9.5 Inch Axle))Drive Pinion Flange/Yoke and/or Oil Seal Replacement
(10.5 Inch Axle)  (See: Pinion Flange/Service and Repair/Drive Pinion Flange/Yoke and/or Oil Seal Replacement (10.5 Inch Axle)) .

12. Install the pinion into the axle housing.
13. Install the pinion yoke. Refer to Drive Pinion Flange/Yoke and/or Oil Seal Replacement (8.6/9.5 Inch Axle)  (See: Pinion Flange/Service and

Repair/Drive Pinion Flange/Yoke and/or Oil Seal Replacement (8.6/9.5 Inch Axle))Drive Pinion Flange/Yoke and/or Oil Seal Replacement (10.5
Inch Axle)  (See: Pinion Flange/Service and Repair/Drive Pinion Flange/Yoke and/or Oil Seal Replacement (10.5 Inch Axle)) .

14. Install the differential assembly. Refer to Differential Replacement (8.6/9.5 Inch LD Axle)  (See: Service and Repair/Removal and

Replacement/Differential Replacement (8.6/9.5 Inch LD Axle))Differential Replacement (10.5 Inch Axle)  (See: Service and Repair/Removal and
Replacement/Differential Replacement (10.5 Inch Axle)) .

15. Fill the axle with lubricant. Use the proper fluid. Refer to Rear Axle Lubricant Replacement (8.0/8.6 Inch Axle)  (See: Fluid - Differential/Service

and Repair/Removal and Replacement/Rear Axle Lubricant Replacement (8.0/8.6 Inch Axle))Rear Axle Lubricant Replacement (10.5 Inch Axle) 
(See: Fluid - Differential/Service and Repair/Removal and Replacement/Rear Axle Lubricant Replacement (10.5 Inch Axle)) .

16. Lower the vehicle.

Ring Gear, Differential > < Drive Pinion Housing and/or Seal Replacement|Page 15708