Dakota 2WD V8-4.7L Flex Fuel (2009)
The no-fuse indicator gives an indication to the vehicle operator when the Ignition Off Draw (IOD) fuse is ineffective or is not installed. This indicator is
controlled by the instrument cluster logic circuit based upon cluster programming and electronic messages received over the Controller Area Network
(CAN) data bus from the Front Control Module (FCM).
The no-fuse indicator function of the odometer Vacuum Fluorescent Display (VFD) unit is completely controlled by the instrument cluster logic circuit.
This logic only allows the indicator to operate when the instrument cluster receives a battery current input on the fused ignition switch output (run-start)
circuit. Therefore, the odometer VFD no-fuse indication is always off when the ignition switch is in any position except ON or START. The instrument
cluster turns on the no-fuse indicator for the following reasons:
-
No-Fuse indicator lamp-on message - Each time the ignition switch is turned to the ON position and the cluster receives an electronic no-fuse
indicator lamp-on message from the FCM indicating that the IOD fuse is missing or ineffective, the no-fuse indicator illuminates. The indicator
remains illuminated for about three seconds, until the IOD fuse installs, until the trip odometer reset switch button pressed or until the ignition
switch is turned to the OFF position, whichever occurs first.
The FCM continually monitors the IOD circuit to determine the status of the IOD fuse, then sends the proper lamp-on or lamp-off message to the
instrument cluster, also known as the Cab Compartment Node (CCN) over the CAN data bus.
Use a diagnostic scan tool is required for proper diagnosis of the no-fuse indicator, the FCM, the CCN, the CAN data bus or the electronic
communication related to no-fuse indicator operation. Refer to the appropriate diagnostic information.
Transmission Temperature Indicator - Description
DESCRIPTION
A transmission over-temperature indicator is standard equipment on all instrument clusters. However, on vehicles not equipped with an optional
automatic transmission, this indicator is electronically disabled. This indicator is located in the center of the speedometer, in the area above and to the
right of the speedometer needle hub.
The transmission over-temperature indicator consists of a stencil-like cutout of the International Control and Display Symbol icon for Transmission
Temperature in the opaque layer of the instrument cluster overlay. The dark outer layer of the overlay prevents the indicator from being clearly visible
when it is not illuminated. A red Light Emitting Diode (LED) behind the cutout in the opaque layer of the overlay causes the indicator to appear in red
through the translucent outer layer of the overlay when it is illuminated from behind by the LED, which is soldered onto the instrument cluster electronic
circuit board.
The transmission over-temperature indicator is serviced as a unit with the instrument cluster.
Transmission Temperature Indicator - Operation
OPERATION
The transmission over-temperature indicator gives an indication to the vehicle operator when the transmission fluid temperature is excessive, which may
lead to accelerated transmission component wear or failure. This indicator is controlled by a transistor on the instrument cluster circuit board based upon
cluster programming and electronic messages received by the cluster from the Powertrain Control Module (PCM) over the Controller Area Network
(CAN) data bus.
The transmission over-temperature indicator Light Emitting Diode (LED) is completely controlled by the instrument cluster logic circuit. This logic only
allows the indicator to operate when the instrument cluster receives a battery current input on the fused ignition switch output (run-start) circuit.
Therefore, the LED is always off when the ignition switch is in any position except ON or START. The LED only illuminates when it is provided a path
to ground by the instrument cluster transistor. The instrument cluster turns on the transmission over-temperature indicator for the following reasons:
-
Bulb Test - Each time the ignition switch is turned to the ON position the transmission over temperature indicator is illuminated for about two
seconds as a bulb test.
-
Trans Over-Temp Indicator Lamp-On Message - Each time the cluster receives an electronic transmission over temp indicator lamp-on
message from the PCM indicating that the transmission fluid temperature is 135 °C (275 °F) or higher, the indicator illuminates and a single chime
tone is sounded. The indicator remains illuminated until the cluster receives a lamp-off message from the PCM, or until the ignition switch is
turned to the OFF position, whichever occurs first. The chime tone feature only repeats during the same ignition cycle if the indicator is cycled off
and then on again by the appropriate lamp-on and lamp-off messages from the PCM.
-
Self Test - Each time the cluster is put through the self test, the transmission over temperature indicator turns on, then off again during the bulb
check portion of the test to confirm the functionality of the LED and the cluster control circuitry.
