Durango 2WD V8-5.9L VIN Z LDC (2000)
NOTE:
THE TRANSMISSION OIL TEMPERATURE MUST BE BETWEEN 80 - 110°F (27 - 43°C).
1).
Start the engine only when the engine and ignition have been off for at least ten (10) minutes.
2).
With the vehicle at a stop and the service brake applied, record the UD CVI while performing a Neutral to Drive shift. During the shift, the UD
CVI will temporarily show a different value which is the 1st N-1 UD CVI. The 1st N-1 UD CVI account for air entrapment in the UD clutch that
may occur after the engine has been off for a period of time.
3).
Repeat steps 1 and 2 until the recorded 1st N-1 UD CVI value stabilizes.
NOTE:
IT IS IMPORTANT THAT THIS PROCEDURE BE PERFORMED WHEN THE TRANSMISSION TEMPERATURE IS BETWEEN 80 - 110°F
(27 - 43°C). IF THIS PROCEDURE TAKES TOO LONG TO COMPLETE FULLY FOR THE ALLOWED TRANSMISSION OIL
TEMPERATURE, THE VEHICLE MAY BE RETURNED TO THE CUSTOMER WITH AN EXPLANATION THAT THE SHIFT WILL
IMPROVE DAILY DURING NORMAL VEHICLE USAGE. THE TCM ALSO LEARNS AT HIGHER OIL TEMPERATURES, BUT THESE
VALUES (LINE PRESSURE CORRECTION VALUES) ARE NOT AVAILABLE FOR VIEWING ON THE DRB III(R).
Procedure To Learn A Smooth Neutral To Drive Garage Shift:
Perform this procedure if the complaint is for a delayed or harsh shift when the transmission is put into gear after the vehicle has had its first shift. Use
the following steps to have the TCM learn the N-1 UD CVI.
NOTE:
THE TRANSMISSION OIL TEMPERATURE MUST BE BETWEEN 80 - 110°F (27 - 43°C).
1).
Start the vehicle engine and shift to drive.
2).
Move the vehicle forward to a speed of at least 10 MPH and come to a stop.
3).
Perform repeated N-1 shifts at a stop while pausing in Neutral for at least 2-3 seconds and monitor UD CVI volume until the value stabilizes. The
value will change during the N-D shift. This is normal since the UD value is different for the N-1 shift then the normal value shown which is used
for 4-3 coastdown and kickdowns. Perform repeated shifts in this temperature range until the UD CVI value stabilizes and the N-1 shifts become
smooth.
Procedure To Learn The 1st 2-3 Shift After A Restart Or Shift To Reverse:
Use the following steps to have the TCM learn the 1st 2-3 shift OD CVI.
NOTE:
THE TRANSMISSION OIL TEMPERATURE MUST BE ABOVE 80°F (27°C).
1).
With the vehicle engine running, select reverse gear for over 2 seconds.
2).
Shift the transmission to Drive and accelerate the vehicle from a stop at a steady 15 degree throttle opening and perform a 2-3 shift while noting
the OD CVI. During the shift, a different value will appear on the screen, which is the 1st 2-3 OD CVI.
3).
Repeat steps 1 and 2 until the 1st 2-3 upshift becomes smooth and the 1st 2-3 OD CVI stabilizes.
Procedure To Learn A Smooth 2-3 And 3-4 Upshift:
Use the following steps to have the TCM learn the OD and 4C CVI's.
NOTE:
THE TRANSMISSION OIL TEMPERATURE MUST BE ABOVE 110°F (43°C).
1).
Accelerate the vehicle from a stop at a steady 15 degree throttle opening and perform multiple 1-2, 2-3, and 3-4 upshifts. The 2nd 2-3 shift
following a restart or shift to reverse will be shown during the shift as a value between the 1st 2-3 OD CVI and the normal OD CVI. Updates to the
normal OD CVI will occur after the 2nd shift into 3rd gear, following a restart or shift to reverse.
2).
Repeat step 1 until the 2-3 and 3-4 shifts become smooth and the OD and 4C CVI become stable.
Procedure To Learn A Smooth 4-3 Coastdown And Part Throttle 4-3 Kickdown:
Use the following steps to have the TCM learn the UD shift volume.
