Viper GTS V10-8.0L VIN E (1999)
Body Control Module: Description and Operation
Airbag System
Airbag System Description
AIRBAG SYSTEM
The Airbag Control Module (ACM) is secured to a bracket on the floor panel transmission tunnel below the instrument panel inside the vehicle.
The ACM mounting bracket also serves as the instrument panel center support. The microprocessor contains the airbag system logic. The ACM
system logic includes On-Board Diagnostics (OBD) capability, and communications with the instrument cluster circuitry on the Chrysler Collision
Detection (CCD) data bus to control the airbag indicator lamp.
The microprocessor in the ACM monitors the impact sensor signal and the airbag system electrical circuits to determine the system readiness. If
the ACM detects a monitored system fault, it sends a message to the instrument cluster on the CCD data bus to turn on the airbag indicator lamp. A
pre-programmed decision algorithm in the ACM microprocessor determines when the deceleration rate signaled by the impact sensor indicates that
the impact is severe enough to require airbag protection. When the programmed conditions are met, the ACM sends an electrical signal to deploy
the airbag system components.
Only one impact sensor is used in this airbag system. The impact sensor is an accelerometer that senses the rate of vehicle deceleration, which
provides verification of the direction and severity of an impact. The impact sensor is calibrated for the specific vehicle, and is only serviced as a
unit with the ACM.
The ACM also contains an energy storage capacitor. This capacitor stores enough electrical energy to deploy the airbags, for one second
following a battery disconnect or failure during an impact. The purpose of the capacitor is to provide the airbag system protection in a severe
secondary impact if the initial impact has damaged or disconnected the battery, but was not severe enough to deploy the airbags.
THE AIRBAG SYSTEM IS A SENSITIVE, COMPLEX ELECTROMECHANICAL UNIT. BEFORE ATTEMPTING TO DIAGNOSE OR
SERVICE ANY AIRBAG SYSTEM OR, RELATED STEERING WHEEL, STEERING COLUMN, OR INSTRUMENT PANEL
COMPONENTS YOU MUST FIRST DISCONNECT AND ISOLATE THE BATTERY NEGATIVE (GROUND) CABLE. THEN WAIT TWO
MINUTES FOR THE SYSTEM CAPACITOR TO DISCHARGE BEFORE FURTHER SYSTEM SERVICE. THIS IS THE ONLY SURE WAY
TO DISSABLE THE AIRBAG SYSTEM. FAILURE TO DO SO COULD RESULT IN ACCIDENTAL DEPLOYMENT AND POSSIBLE
PERSONAL INJURY.
NEVER STRIKE OR KICK THE AIRBAG CONTROL MODULE, AS IT CAN DAMAGE THE IMPACT SENSOR OR AFFECT ITS
CALIBRATION. IF AN AIRBAG CONTROL MODULE IS ACCIDENTALLY DROPPED DURING SERVICE, THE MODULE HAS TO BE
SCRAPPED AND REPLACED WITH A NEW UNIT.
The airbag warning lamp is the only point at which the customer can observe "symptoms" of a system malfunction. Whenever the ignition key is
turned to the "start" or "run" position, the ACM performs a lamp check by turning the AIRBAG warning lamp on the 6 to 8 seconds. If the lamp
remains oft, it means that the ACM has checked the system and found it to be free of discernible malfunctions. If the lamp remains on, there could
be an active fault in the system or the MIC lamp circuit may be internally shorted to ground. If the lamp comes on and stays on for a period longer
than 6 to 8 seconds then goes oft, there is usually an intermittent problem in the system.
Perform the WARNING LAMP OPEN/SHORTED procedure to find the cause of any customer complaint regarding the AIRBAG warning lamp,
such as:
-
warning lamp does not illuminate
-
warning lamp stays illuminated with no active DTC's
The ACM cannot be repaired or adjusted and, if damaged or faulty, it must be replaced.
Driver Airbag Module (DAB)
DRIVER AIRBAG MODULE (DAB)
The airbag protective trim cover is the most visible part of the driver side airbag system. The module is mounted directly to the steering wheel.
Located under the trim cover are the horn switch, the airbag cushion, and the airbag cushion supporting components. The airbag module includes a
housing to which the cushion and inflator are attached and sealed. The airbag module cannot be repaired, and must be replaced if deployed or in
any way damaged. The inflator assembly is mounted to the back of the airbag module. The inflator seals the hole in the airbag cushion so it can
discharge the gas it produces directly into the cushion when supplied with the proper electrical signal. The protective trim cover is fitted to the
front of the airbag module and forms a decorative cover in the center of the steering wheel. Upon airbag deployment, this cover will split at
predetermined breakout line.
THE AIRBAG MODULE INFLATOR ASSEMBLY CONTAINS SODIUM AZIDE AND POTASSIUM NITRATE. THESE MATERIALS ARE
POISONOUS AND EXTREMELY FLAMMABLE. CONTACT WITH ACID, WATER, OR HEAVY METALS MAY PRODUCE HARMFUL
AND IRRITATING GASES (SODIUM HYDROXIDE IS FORMED IN THE PRESENCE OF MOISTURE) OR COMBUSTIBLE
COMPOUNDS. IN ADDITION, THE PASSENGER AIRBAG MODULE CONTAINS ARGON GAS PRESSURIZED TO OVER 2500 PSI.
