| Removal and Installation All vehicles | | -
Remove the rear door trim panel.
For additional information, refer to: Rear Door Trim Panel - Vehicles With: Manual Windows (501-05 Interior Trim and Ornamentation, Removal and Installation) /
Rear Door Trim Panel - Vehicles With: Power Windows (501-05 Interior Trim and Ornamentation, Removal and Installation).
| | | -
Remove the exterior rear door handle.
For additional information, refer to: Exterior Rear Door Handle (501-14 Handles, Locks, Latches and Entry Systems, Removal and Installation).
| | | -
Remove the rear door window regulator grommets. | Vehicles with manual windows | | -
Install the window regulator handle. - Using the rear door window regulator handle, align the window glass clamp bolts with the access holes.
| | | -
Loosen the rear door window glass clamp bolts. | | | -
Raise the rear door window glass. | | | -
Using suitable tape, secure the rear door window glass to the rear door. | Vehicles with power windows | | -
Connect the battery ground cable.
For additional information, refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).
| | | -
Using the front door power window control unit, align the rear door window glass clamp bolts with the access holes. | | | -
Loosen the rear door window glass clamp bolts. | | | -
Raise the rear door window glass. | | | -
Using suitable tape, secure the rear door window glass to the rear door. | | | -
Disconnect the battery ground cable.
For additional information, refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).
| All vehicles | | -
Detach and disconnect the rear door wiring harness. | 15. Remove the components in the order indicated in the following illustration(s) and table(s). 1 - Rear door latch bracket retaining screw 2 - Rear door latch retaining bolts 16. To install, reverse the removal procedure. Removal Details Item 3 : Rear door latch remote control cable | | -
Using a suitable screwdriver, latch the rear door lock into the closed position. | | | -
Detach the rear door latch remote control cable from the rear door latch remote control handle. - Operate the door latch remote control handle lock to the lock position.
- Release the remote control cable retaining clips.
- Detach the inner remote control cable from the remote control handle lock lever.
| Item 4 : Rear door lock actuator retaining screw | | -
Detach the rear door lock actuator. - Loosen the door lock actuator retaining screw.
- Release the door lock actuator retaining clip.
- Slide the door lock actuator towards the front of the vehicle.
| Item 5 : Rear door wiring harness | | -
Detach and push the rear door wiring harness into the rear door. | Item 6 : Rear door inner panel CAUTION:When removing the front door inner panel, do not trap or place excessive strain on the door wiring harness. Item 7 : Rear door lock actuator | | -
Detach the rear door lock actuator from the latch support bracket. | Item 8 : Exterior rear door handle remote control cable | | -
Detach the exterior rear door handle remote control cable from the rear door lock actuator. - Using a suitable flat blade screwdriver, release the exterior rear door handle remote control cable retaining clips.
- Slide the exterior rear door handle remote control cable off the rear door lock actuator retainers.
| | | -
Align the exterior rear door handle remote control inner cable with the slot in the door lock actuator and remove. | Installation Details Item 6 : Rear door inner panel | | -
Before installing the rear door inner panel retaining bolts, feed the door wiring harness electrical connector through the rear door wiring harness hole. | Item 4 : Rear door lock actuator retaining screw | | -
Install the rear door lock actuator to the rear door. | | | -
Tighten the rear door lock actuator retaining screw. | |
